CTX18LYZDRWH Hotpoint Refrigerator - Instructions

Unplugged refrigerator.Checked that new gasket was the right size for freezer.Opened freezer door and lifted inside edge to access screw's. Loosened top screw's and screw's half way down each side and pulled gasket out. Installed new gasket into slot where old gasket was and tightened screw's across top and the first couple down side's.Lifted edge of old gasket and loosened screw's holding remainder of old gasket in place and finished removing old gasket.Finished putting new gasket in slot and tightened remaining screw's. The reason for only doing gasket half at a time is to keep the door square and not getting out of shape. If new gasket is warped when removed from shiping box run under hot water or soak in hot water until more flexible.

Simple install. .

Referenced a couple of videos first, held up the new gasket to ensure fit, then carefully pulled the old gasket off by hand. Wiped down the ridges/edges of the door, then installed new gasket first on opposite corners then along all sides. Simply pressed in to the door ridges/bracket. Used a putty knife to ensure the edge of gasket was not folded under itself, and the blunt edge of the handle to ensure it was snugly installed all the way around. Didn’t have to remove the door as I had expected to. Very easy and took maybe 30 mins.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

At this time of the year our beach fridge is always full of food and drinks. Every time we want something it meant leaving the door open for extended time whlie moving things left, right and center. When the new shelf arrived I removed the food and drinks from the existing two shelves and moved them closer together. I then slipped in the new shelf and reloaded the food. Suffice to say the fridge stays open less and we are able to get at things without moving others. I wish I had thought to do this before.

Went on YouTube and it had excellent instructions for removal and installation

Well, when I opened the package the gasket was bended in half so I opened it and put it first on the floor and after some minutes I put it on the refrigerator side.
Then I took a screwdriver and easily removed the old gasket, cleaned the the channel where the new gasket had to seat or be inserted. Then I took the new gasket and put it on place and begining on the top right corner I began to insert the gasket into the channel from the right to the left. Double check to see if was ok
I continued on both sides from top to the bottom, one by one.
When I reached the bottom I began from the left to the right inserting the gasket into the channel. To complete the installation at the bottom I had to pull the gasket a little to properly reach the corner and I finished
To make sure the gasket was on place I hit the gasket with my bare hand all around and I was done.
It was very easy, I just followed the instructions given by the manufacturer

I opened the fridge door removed the tape the customer had on it to keep in place. Gasket was super worn out I pulled in it to remove it. Cleaned it where the new gasket was gonna insert. Put the new gasket in place and with my thumb applied some pressure till I heard a small snap. Did the same all the way around and closed and opened the door to check it all around making sure it was in place and sealing all around.

Removed the door by removing the two screws holding it on. Do not try to do this repair with the door attached. Easily removed the old gasket. Getting the new one on the door was EXTREMELY difficult. I couldn't do it. After 90 minutes, I gave up and called my appliance repairman. When he arrived, he and I worked together to get the new gasket on the door. It took 2 sets of hands to do this. It still took us about 40 minutes. My repairman had a few choice words about the design of the system holding the gasket on the door. Ditto for me. So the cost of my repair was doubled because I had to pay the repairman to help me attach the new gasket. I should have just bought a new fridge.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

replaced lights in refrigirator and freezer

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

I did not do the repair but observed a friend trying to replace gasket in refrigerator. It was a very difficult procedure. He works as a handyman so he knew what he was doing and had to manually fit gasket with some help with a hammer. Gasket did not go in easy and had to be forced to fit until job completed/

Easy