Models > CTX18LYZDRWH

CTX18LYZDRWH Hotpoint Refrigerator

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for CTX18LYZDRWH

Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
This 40-Watt light bulb is sold individually. It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges,...
In Stock
Order now and your part arrives by Apr 6
This white fresh food door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air out.
In Stock
Order now and your part arrives by Apr 6
This white door gasket is used to seal the freezer door when closed.
In Stock
Order now and your part arrives by Apr 6
This part is the replacement stationary wire shelf for your refrigerator. It is white in color and is approximately 24 1/2 inches by 14 3/8 inches. The stationary wire shelf rests on grooves in the re...
In Stock
Order now and your part arrives by Apr 6
This door shelf retainer bar is a manufacturer-approved replacement part for your refrigerator. This bar is made of white plastic and is about 21 1/4 inches in length and 2 inches deep. It helps keep ...
In Stock
Order now and your part arrives by Apr 6
In Stock
Order now and your part arrives by Apr 6
$15.26
In Stock
Order now and your part arrives by Apr 6
Special Order
$61.55
The filter dryer filters refrigerant that travels through the sealed system of the refrigerator.
In Stock
Order now and your part arrives by Apr 6
No Longer Available
No Longer Available

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for CTX18LYZDRWH

Viewing 7 of 7
Door Sweating
Fixed by these parts
Fixing Fixing
How to fix it
Fridge too warm
Fixed by these parts
Fixing
How to fix it
Door won’t open or close
Fixed by these parts
Fixing
How to fix it
Freezer section too warm
Fixed by these parts
Fixing
How to fix it
Frost buildup
Fixed by these parts
Fixing
How to fix it
Leaking
Fixed by these parts
Fixing
How to fix it
Fridge runs too long
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Thomas from key west, FL
Parts Used:
WR24X10228
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Freezer door gasket was torn and loose.
Unplugged refrigerator.Checked that new gasket was the right size for freezer.Opened freezer door and lifted inside edge to access screw's. Loosened top screw's and screw's half way down each side and pulled gasket out. Installed new gasket into slot where old gasket was and tightened screw's across top and the first couple down side's.Li fted edge of old gasket and loosened screw's holding remainder of old gasket in place and finished removing old gasket.Finished putting new gasket in slot and tightened remaining screw's. The reason for only doing gasket half at a time is to keep the door square and not getting out of shape. If new gasket is warped when removed from shiping box run under hot water or soak in hot water until more flexible.
69 of 92 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Hollis from Daphne, AL
Parts Used:
WR71X10378
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Neeed extra shelves for new purchased refrigerator
Simple install. .
22 of 35 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joe from BROOKLINE, MA
Parts Used:
WR24X10236
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Old door gasket torn/problematic; moisture in fridge
Referenced a couple of videos first, held up the new gasket to ensure fit, then carefully pulled the old gasket off by hand. Wiped down the ridges/edges of the door, then installed new gasket first on opposite corners then along all sides. Simply pressed in to the door ridges/bracket. Used a putty knife to ensure the edge of gasket was no t folded under itself, and the blunt edge of the handle to ensure it was snugly installed all the way around. Didn’t have to remove the door as I had expected to. Very easy and took maybe 30 mins.
14 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!