CSK25GRZBAA Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack from Ft Myers, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
air leak from ice maker flap permitting frost buildup inside ice maker dispenser
Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from Katy, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The rubber seal on the flapper came off.
My husband made the replaced the flapper while watching the video provided in your email, it was easy. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Concord, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost in and around ice maker outlet
Followed the video directions. Spent about 5 minutes and I was done. Very easy to do. Problem with frost is gone. The video makes it easy to remove the plastic parts without any damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Glendora, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inside freeze was frosting up
used a flat screwdriver to pop off out side cover then remove 6 screws took off plate. Pulled off the flapper and replaced. less the 15 mins and fixed the issue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Little Elm, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost buildup in the freezer near the ice chute.
I watched the video on the PartSelect.com website and decided to give it a try. The replacement of the flapper was even easier than I anticipated! The old flapper was extremely warped and was allowing air into the freezer. I'm not sure how/why it was in that condition but I am happy to report that I have no more ice buildup. Thank you, PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Pittsboro, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The flapper on the freezer was warped and allowed humidity to create frost in the freezer.
I watched the how to video and followed the instructions. The entire repair took less than 4 minutes. Hardest thing was disconnecting the control panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THEOTIS from CHARLOTTE, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator COnstant running and low ice output
I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GWEN H from CONCORD, CA
- Parts Used:
- WR32X1492
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Upper Vegetable Pan
The hardest part was getting hte right replacement drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Reston, VA
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer light shield broke from mount
I am clueless around the house. But this was easy: Removed ice maker bin, fiddled with freezer shield to line up with the single screw hole that holds it in place. Use screwdriver to install shield with original screw that stayed in place after the original freezer mount cracked and broke. Put ice maker bin back. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andy from clearwater, FL
- Parts Used:
- WR32X1492
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pan right edge is broken
Pull out old pan,remove the vent cover from front and install it on the new pan, done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Colorado Springs, CO
- Parts Used:
- WR71X1936
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing a shelf in freezer
I saved about $15.00 by ordering the part on line. It came in about a week and was a super easy process. Since it was just missing there really wasn't anything that needed fixing. just installed it where it belonged and all was good. Great and easy experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Fripp island, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
3rd Flap for this Ice Mkaer, keeps warping
Very Easy, follow direction I the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Paducah, KY
- Parts Used:
- WR30X256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Collar that holds Ice auger assemble was Broken.Seems to be a manifacturing defect in this model.
I simply ordered a new Ice bucket, removed about 6 Phillips head screws, removed the old bucket from the Ice door and replaced with a new bucket. SIMPLE !!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Chester Springs, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper was warpped
Follow instruction on the video you provided
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Hughesville, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice dispenser chute kept freezing with condensation
The flapper on the ice chute was curled up and not creating a good seat, so the chute kept clogging up with frozen condensation, especially during the humid summer months. The online video made it so easy to replace the part myself. I was able to fix the problem in under 15 minutes and at a fraction of the price!
Was this instruction helpful to you?
Thank you for voting!