CSK22GABCAD Hotpoint Refrigerator - Instructions

Empty all the good stuff stored in the door. Remove top hinge, lift off door. Remove bottom hinge from door and refrigerator, replace with new hinges. Replace door and reinstall top hinge. Very simple. Worst part was removing all the stuff stored in the door then putting it back! My parts arrived very quickly and I'm very pleased with Part Select.

With my wife's help, we emptied the door shelves and removed the door to the kitchen table. The video and instructions for replacing the parts were 100% right. We probably spent more time cleaning the door bottom and gasket than actually changing the hinge assembly! The job went very smoothly and saved us from overspending on a repair to this old fridge, or worse, making a quick decision on buying a new one.

I watched the "How To" video on the Parts Select web site twice. The video was very helpful, kind of like having someone right there with you showing you how to replace the hinge. I emptyed the door shelves, removed the top hinge hexscrews and easily lifted the door off the lower hinge, pieces of the broken cam hinge on the door fell off. I set the door on the floor in front of the sink with the handle edge on the floor. I unbolted the hinge and installed the new one. I loosened one screw on the door cam hinge and removed the other, easily replacing the broken part. Before tightening the screws I checked to make sure the hinge hole in the door was not blocked by the new cam hinge. I lifted the door and water ran out from somewhere. I tried to set the door on the lower hinge several times with no luck. I rechecked the hole, it was still clear. I tried placing the door on the refrigerator using the seal to hold it in place, that worked but I couldn't get the door to drop down onto the hinge. I played with it some more and finally got it in place, reinstalled the top hinge, mopped up the water and tried the door. It didn't self close. I adjusted the top hinge a couple of times and applied a little silicone to the hinges, it still didn't self close. I told my wife to make sure the door closes completely and reloaded the stuff into door. After a couple of days it now closes by itself like it's supposed to. In retrospect, I was alone doing the replacement and it really was an easy job but a second person to help line up the lower hinge would have helped a lot.

I watched the repair video. Replaced the cam on the bottom of the door and the hinge pin. Now the door closes on its own, just like brand new.

Removed top hinge, lifted door from bottom post. Removed post with nut driver/socket, removed corresponding bracket/receiver from door. Attached new parts to refrigerator base and bottom edge of door. Was careful to replace part pieces in the same order as original, and secured tightly. Lifted door onto bottom hinge post, leveled the door and replaced top hinge.

Followed the video to replace bottom hinge assembly. The only hiccup was that the video instruction was for the fridge side door, so there wasn't step by step instruction for dealing with the electrical connection at the top of door or the water line at the bottom. However, it was simple enough to figure out. Replacement took about 20-25 mins.

Removed door with little or no difficulty. Only time consuming portion of repair was disconnection and reconnecting of water line to door. This difficulty was primary due to age of the unit. After repairing, I determined that the cam on the refrigerator was also damaged so ordered same part to replace the refrigerator side.

This was a Mother/Daughter feat. We viewed the video based on the bottom hinge assembly part that we had ordered. We did it exactly as shown and it was so easy. But while we had the door off we also had a chance to really clean the frigerator inside out. We were extremely happy that we were able to repair the frigerator oursleves and how much money we had saved by doing it. Thanks

Watched PartSelect video and did exactly as video said. Had finished product in less than 30 minutes.6 bolts and one screw.

like the man in the cd

After receiving the part (quickly) my son-in-law replaced the old one without any trouble. Thanks very much

I replaced both bottom hinges on my GE refrigerator. The hint that they were worn out was that both the freezer door and fresh food door would not close completely. You had to lift the door on the hinge to get it to close. Many of the GE service repair people recommend complete removal of each door to replace the bottom hinge. I found I could use a couple of wood blocks tall enough to take the weight of the door, jacking it up off of the hinge so could loosen the hex head screws. The freezer door hinge took a few minutes longer because the water supply line for the icemaker which is routed through the tube in the hinge. Overall, an easy repair and the cost of two repair visits was saved.

Removed the top hinge of the right-hand door, removed the door, replaced the cam riser on the bottom of the door, then replaced the door and top hinge. Simple and easy.

I watched the video and did the job as instructed. It was very easy and worked as expected. The video was the key.

I watched your video on the repair twice and then did the repair. . . Your video was a major help and the only reason I decided to do the repair myself. . . The video was excellent and gave m e info on every detail of the repair. . . . . Thanks