CSX19LABBWH Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jim from Camarillo, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Door wouldn't automatically close, dropped a bit
First removed plastic cover off top hinge with phillips screwdriver. Used nut driver to loosened screws on upper hinge to 1/2 inch out and then used wood blocks to shim up door as high as possible while still in closed position. Used socket wrench to remove lower hinge and fitting from bottom of door, while still closed. Installed new lower hinge and door fitting with socket wrench. Lowererd door to sit on bottom hinge and then adjusted position of top hinge before tightened those screws with nut driver. Reinstalled plastic cover. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Millersville, MD
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
HInge Cam Riser next to lower door hinge broke and door would not close
The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.
Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.
Easy job .. around 20 minutes.
Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.
Easy job .. around 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duncan from Franklin, TN
- Parts Used:
- WR02X10140
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door wouldn't open/shut properly.
I could see a broken part but couldn't tell exactly how it was oriented on the hinge. I bought just the cam riser but then thought I needed the hinge kit based on what I read on this site. Then I saw better pictures of the hinge kit on another site & realized there are 2 cam risers that meet. The one riveted to the hinge was fine (in my case) - I only needed the upper one...a very inexpensive repair. Do NOT remove the door for this repair. Slide the door up a bit while closed and use a pint-sized paint can to prop it up. Make the repair and remove the can...done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Woodstock, GA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door would not close properly.
Removed door and replaced bracket assembly. Door works like new. Self closing and sealing properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zach from Glenwood Springs, CO
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door wouldn't close and open properly
Removed guards and covers, (2 snap connections, 3 phillips head screws) Removed two 5/16" screws, removed door, removed cam from bottom of door, installed new items.
Worked Great!!!
Worked Great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Coventry, CT
- Parts Used:
- WR02X10140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Cam riser broken
Removed trim cap at top of door. Removed two hex head screws and lifted top hinge off door. Lifted door off lower hinge. Unscrewed broken cam riser from bottom of door and replaced with new part which was then screwed into place. Replaced door on lower hinge, Replaced upper hinge onto top of door, replaced screws and replaced trim.
Easy peasy. :-)
Easy peasy. :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from hillsboro, NH
- Parts Used:
- WR02X10140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Cam Riser worn out
very easy, thanks for the great selection for parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Austin, TX
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The cams that allow the fridge door to automatically close had worn out
First I bought the right tool to remove the hinges.
Then replaced the hinge with the two cams.
Now the door closes itself.
Then replaced the hinge with the two cams.
Now the door closes itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from burns, TN
- Parts Used:
- WR02X10140
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
cam riser broke and needed replacing
Just remove all items in door shelves, remove screw holding top hinge cover on. Remove two bolts holding top hinge and remove hinge from door. Carefully open door and lift out of bottom hinge. Remove screw holding bottom hinge on door and replace broking cam riser. Reinstall door in reverse order and adjust top hinge where both doors are even across the top. Thats it!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vickie from Chandler, OK
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Refrigerator hinge broke
Use several wood blocks and propped fridge dooe up and someone else steadied the door while I replaced the hinge. Pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from lesage, WV
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door stop broke
they sell the cam piece but the instructions says not to replace only one part. so beware you need both the cam and hinge as a kit .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Holbrook, NY
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door closing cams, top and bottom, became damaged and needed replacement
Turned refrigerator off. Removed food from right hand (refig.) door. Closed door. Removed upper hinge cover with a standard Phillips screwdriver and then removed upper hinge by removing two 5/16" bolts using nutdriver. Lifted door up to clear the bottom hinge-post and set it on the table. Removed the kick pan at the bottom of the refrigerator and then removed the bottom hinge-post which was attached with two more 5/16" bolts. Installed new lower hinge post and rubbed a small amount of mineral oil on the closing cam (which is riveted to the hinge-post). Removed the old upper closing cam from the door (5/16" bolts) while it as lying horizontal on the table and installed new cam lubricated with a small amount of mineral oil. dropped the door in place, replaced upper hinge and cover. Replaced kick pan. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CLAUDE from TEXAS CITY, TX
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Freezer Door Not Closing Completely
After reading other posted comments,I ordered a new hinge assembly set ps290199. My helper and I removed the door and laid it on the kitchen table. While he replaced the hinge on the refigator,I replaced the cam on the door bottom. We re-hung the door and completed the job in 15 minutes with the door closing like it did when new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rocklin, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door sagged and would not stay closed
Don't even need to empty the shelves in the door.
Just prop the door up with a block of wood from the floor to the bottom of the door. Lay on the floor and replace the parts.
The door was acting up for a long time. I wish I had researched and repaired the problem a long time ago. Now it works great!
Just prop the door up with a block of wood from the floor to the bottom of the door. Lay on the floor and replace the parts.
The door was acting up for a long time. I wish I had researched and repaired the problem a long time ago. Now it works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Waterford, MI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door closing cam desintegrated
Took the stuff out of the door
Removed the door
Replaced the hinge
Put the door back in
Put the stuff back in the door
You may be thinking that I'm not much for words - but this was SO EASY that it doesn't warrant using more words than I did.
My 7-year-old son helped me - it was a fun father-son project.
Removed the door
Replaced the hinge
Put the door back in
Put the stuff back in the door
You may be thinking that I'm not much for words - but this was SO EASY that it doesn't warrant using more words than I did.
My 7-year-old son helped me - it was a fun father-son project.
Was this instruction helpful to you?
Thank you for voting!