CSK20GABCAD Hotpoint Refrigerator - Instructions

Removed food and trays from door. This took longer than the actual repair. Removed top hinge cover (1 phillips screw) and top hinge (2ea 5/16" hex bolts). Removed door, replaced hinge assembly on refrigerator (2ea 5/16" hex bolts)which included a new hinge cam (they don't tell you this, but the cam is included in the assembly so you don't need to order a seperate cam) I now have a spare cam. Piece of cake...your mom could do it!!

Same as the others, just propped the door up and took off the upper and lower hinge parts and replaced them. One note: the old hinge was so torn up that some of the shims were partially destroyed. Since I didn't order the shims, I had to do a little machining. It might be a good idea to order shims if there is ant doubt.
P.S. With normal shipping, the order arrived in 2 days!

First issue, I tried to get the top hinge cover off by gently prying. No go. Went to get a step stool and discovered a small screw holding the plastic cover on. At least I didn't break it by prying. I then removed the two top hinge bolts and removed top hinge. I then lifted the door off the bottom hinge.

I then removed the bottom hinge (two bolts) and replaced it with the new hinge with the attached lift cam. (Bottom half of cam)

I then removed the broken lift cam from the bottom of the door, replacing it with the door closing cam included in the hinge assembly package.

Second issue: I did not need to order the DOOR closing cam as a separte item as it came with the hinge assembly package. (There was a warning note in the hinge assembly package to use the door cam included, as new materials had been used and abnormal wear could occure if you didn't replace both pieces of the lift cam)

I set the door back on the bottom hinge, replaced the top hinge and tested. The door would NOT close on it's own. Getting down on my belly I could see resistance of the door light switch was keeping the door from closing. The fix of this issue was to load the door with the normal use items. This provided enough weight to the door and offset the resistance of the switch. EVERY THING WORKED GREAT. Time was 26 minutes from start to finish.

Just watch the Parts Select YouTube videos on replacing the door hinges. That helped a lot.

All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.

1. Unscrewed the top screws with a socket set 2. Took door off of refrigerator 3. Unscrewed hinge assembly 4. Put on new hinge assembly 5. Replaced door on refrigerator 6. Screwed top screws back in I watched a youtube video on how to replace it that was extremely helpful. I am not a handyman, so if I can do this, anyone can.

The on line "how to" video was PERFECT! I followed the steps and the repair was a breeze. Parts Select is now bookmarked in my favorites! These guys make is SO easy for "non-handy" folks like me.

they sell the cam piece but the instructions says not to replace only one part. so beware you need both the cam and hinge as a kit .

Just remove all items in door shelves, remove screw holding top hinge cover on. Remove two bolts holding top hinge and remove hinge from door. Carefully open door and lift out of bottom hinge. Remove screw holding bottom hinge on door and replace broking cam riser. Reinstall door in reverse order and adjust top hinge where both doors are even across the top. Thats it!!!!!

Turned refrigerator off. Removed food from right hand (refig.) door. Closed door. Removed upper hinge cover with a standard Phillips screwdriver and then removed upper hinge by removing two 5/16" bolts using nutdriver. Lifted door up to clear the bottom hinge-post and set it on the table. Removed the kick pan at the bottom of the refrigerator and then removed the bottom hinge-post which was attached with two more 5/16" bolts. Installed new lower hinge post and rubbed a small amount of mineral oil on the closing cam (which is riveted to the hinge-post). Removed the old upper closing cam from the door (5/16" bolts) while it as lying horizontal on the table and installed new cam lubricated with a small amount of mineral oil. dropped the door in place, replaced upper hinge and cover. Replaced kick pan. Done.

Use several wood blocks and propped fridge dooe up and someone else steadied the door while I replaced the hinge. Pretty easy.

Removed the upper hinge assembly. Removed the door. Removed the kick plate. Removed the old hinge assembly and installed the new one.Replaced the other broken cam on the door bottom. Then,reinstalled door to fridge and reinstalled the top hinge. PS/cleaned and lubed both upper and lower hinges.

I simply followed the excellent video, once I discovered the lower door hinge was the problem. Part Select was amazing! A $25 part and 15 minutes saved me $1,200+ ... the price of a replacement refridgerator. Thank you!

I watched the video on your web site first.Then I proceeded to do the repair exactly as the video showed. Very easy!!!!!

The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.

Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.

Easy job .. around 20 minutes.

I could see a broken part but couldn't tell exactly how it was oriented on the hinge. I bought just the cam riser but then thought I needed the hinge kit based on what I read on this site. Then I saw better pictures of the hinge kit on another site & realized there are 2 cam risers that meet. The one riveted to the hinge was fine (in my case) - I only needed the upper one...a very inexpensive repair. Do NOT remove the door for this repair. Slide the door up a bit while closed and use a pint-sized paint can to prop it up. Make the repair and remove the can...done.