CSF22ECB Hotpoint Refrigerator - Instructions

I took the top over off the pivet bracket and used a nut driver to remove the screws on the pivet. Lifted the door off and put on some saw horsess. I revoved the pieces of the old cam on the door by taking out the screw and put the new cam back.
I then drilled out the rivet on the bracket on the door and removed the broken cam. replaced it with the new one and used a screw and nut to replace the rivet. Put the door back and works great now.

completely removed door, then replaced worn-out cam on bottom of door-simple enough; then removed hinge from bottom of refrigerator; removing old cam required drilling out the rivet that fastened cam to hinge; secured new cam to hinge with small machine screw and nut. This procedure is relatively easy but does require minor mechanical ability and having a small drill and bit set. However, replacing the two cams totally fixed the problem.

i'm glad I read this forum before ordering the part because you need two of the door cams. They're sandwiched together on the lower hinge.

I removed the top door hinge, lifted the door off from the lower hinge and layed it on the counter.

I then removed the lower hinge using a nut driver.
I had to grind the rivot head off that holds the door cam onto the hinge and use a nut & bolt to replace
the rivot.

The old plastic door closer cam on bottom of the the door had broken. What was left of it was held on by a hex head screw. There was also a fiber spacer under the cam that was broken. I made a new one out of a piece of aluminum, but cardboard probably would have worked.

Forgot to mention you have to take the door off first--loosen the two screws on the top hinge and lift the door out of the bottom hinge.

I found the self-closing sometimes won't work well until there is some weight in the door.

I Supported the door with wood blocks. Then used a socket wrench to remove both parts of the lower hinge. I had purchased 2 of these plastic closers as recommended. One of them must be cut off with a Dremel Tool or small grinder. A small bolt and nut replaces the rivet that was cut off. Reinstall it just as it was removed. Job complete.
Parts were delivered on time, web site instructions were excellent. I highly recommend PartSelect.com

Followed step-by-step instructions in previous post. Note that there are TWO approaches, both of which work.

Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)

Option 2) Order the entire hinge assembly (PS290199), which includes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)

We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.

Thanks to previous posters for excellent instructions!

Removed two screws on each slide rail and used the same two screws to install new rails. The job took only a few minutes. The best part was the promptness of the delivery. I ordered the parts at 12P on Thurs and had them on my porch at 10A on Fri. Thanks Gary

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Buy ( 2 ) cams !!!! removed hinge cover and hinge on top of the door, ( 2 screws )...lift door off of the bottom hinge and lay door on the floor, remove broken cam on bottom of door with nut driver, ( 2 screws ) , install new cam..... remove the bottom hinge off of the front of the refrigerator with nut driver, (2 screws ).... saw rivit off and remove old cam, install new cam and secure with new bolt and nut,... reinstall hinge back on bottom front of refigerator.....replace door back onto the bottom hinge.....install top hinge back onto the top of the door....replace hinge cover......done !

We taped the door with 3 pieces of duct tape, then put boards under it. Used socket set to remove cam and then cut off rivet so we could just use a screw to keep in place. . . Just for your information, I ordered 2 cams, and was glad I did as I need 2 to make the repair. . . Didn't read about this online or on order recommendation. The cams go 1 up and 1 down thanks for the installation repair stories, it inspired us to "do it ourselves " and we saved about $75 to $100. 00

I watched the video on the webpage and did as he did. it was quick and easy. didn't realize the importance of this little part until it broke

Ther was a video on how to repalce this part on your web site. Describing what tools were needed saved me running back and forth to my tool box. I followed the directions given in the video and repair was completed in 1/2 hour. That included meremoving then cleaning and replacing the sheves in the door. And by the way, the part was shipped the same day I ordered it and arrived on my doorstep noon the following day.

My wife removed the drawer and the glass shelf. Unscrewed the broken rail and screwed in the new one. Replaced the glass shelf and the drawer and she was done.

Removed food from shelf, removed shelf, removed slide. installed new slide. Perfect fit

This is the third time I have used parts select to fix an appliance. I have saved thousands now in replacement costs and certainly hundreds in repair costs. They had exactly what I needed and the online diagrams made it easy to identify the parts I needed and install them too.