HSS25GFPAWW Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donald from Montecello, IN
- Parts Used:
- WR55X10942
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Ice dispencer didn't work
per instructions supplied with main electronic control board. was much easier than I thought it might be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Edmond, OK
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice Maker stopped making ice.
Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from JASPER, GA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Was not making ice cubes
Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Decatur, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Refrigerator Fresh Food condenser iced-up. Frozen side OK
Had to remove all the covers and fans to expose the condenser, which was difficult as the parts were frozen to it. The styrofoam covering the condenser made it almost impossible to defrost it. Therefore, I ripped the styrofoam off to expose the condenser. Was not really difficult to fix the styrofoam cover using metal tape. Replaced temperature sensor in aluminum block, and used butyl sealant to secure. Had to also re-install parts of ice-ball kit that were not well covered. Lots of parts to keep track of, but anyone could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grimes from Bartlett, TN
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
ice maker very slow and arm that controls amount of ice sticking and quit making ice
took 1 screw out and removed ice maker and slid new one in and replace screw and connected power cord
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Broken Arrow, OK
- Parts Used:
- WR55X10942
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Auto dipense of water and ice inop
First determined my modle did not require any of the wire mods descibed on the instructions. Removed power and three cover plate screws. Removed board connectors. Calapsed board anchors and removed board. Removed existing ground wire from board. Installed ground wire on new board and installed board on four mounts. installed connectors and replaced cover and screws. I did wear playtex gloves so as not to cause a static short and wipe out the new board. Took off the bottom panel and cleaned condensor fan cage while I had the fridge out. Secured, plugged in fridge, works real fine, lasts a long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Sebastian, FL
- Parts Used:
- WR38X10380, WR38X10381, WR71X10239
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Metal shelt bracket broke that holds up the glass shelf.
took glass off the old shelf. washed it - replaced the front and back molding replaced the glass into the new metal shelf and ut it back in the refrig. The longest thing was to wash the glass shelf.
Was this instruction helpful to you?
Thank you for voting!
Replacing drawer slide rails on refrigerator.
It was a tough job to replace the drawer slide rails at the bottom of the refrgerator on both the left and right sides. I had to get on the floor on my knees and stomach to get my head inside trying to see the work to be done. First the screws from the broken drawer slide rails had to be removed. The screws in the front part of the rails were a little easier than those in the middle. (Fortunately, there were none in the back.) The screws are hidden in cylindrical grooves and one can't get its head in far enough to see. The middle ones are extremely difficult when on your kneees and stomach. Using a trouble light inside helped a little. The screws in the middle were really tough especially inserting and starting the turning, both in loosening and tightening. Fortunately, I had long nose snips that allowed me to brarely grab the end of the Philips screws and gently insert them in the grooves. Then with luck in aligning the sacrews. I was able to start the tightening but had to use my left hand on the right side as there was no room for my right hand. The total job took a few hours of struggle but I finally finished the job and it was perfect. If I ever have to do it again, I'll know the procedure better. The completion of this task gave me great satisfaction. I think my description here is probably more than neeeded.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Sylva, NC
- Parts Used:
- WR23X10725
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bad switch for door prevented interior light from coming on
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH
Was this instruction helpful to you?
Thank you for voting!
broken slide rails both left and right
Undcrewed broken parts (2 screws each) and replaced with new parts and screwed them back in place,
Was this instruction helpful to you?
Thank you for voting!