HTG25LBMARWW Hotpoint Refrigerator - Instructions

I followed the instructional video. It was right on the money for accuracy in terms of part location and method of replacement.

I ordered the part but my husband had to work out of town for a week. The fridge kept getting warmer, so when the part came I just watched the video on the internet, (bit the bullet) and did the repair just as I saw it done on the video. It was simple and exactly the same as the video. It took a little longer for me because there was a lot of ice built up on the coils, so I used my hair dryer to melt the ice. My refridgerator is working great now.

I took the ice maker out then the panels that closes in the evaporator coil. Disconnected the defrost censer and tested it with an ice bath. The censer did not close the circuit. So it's bad. I got the parts .(Very fast I might add. The PartSelect team did a great job of getting it to me). I the stripped the wires and spliced the like colors back together and tested the censer again with an ice bath. It closed this time. I started the frig and have not heard anything from the client. In this case "No news is good news". Thanks PartSelect

Removed food from Freezer, Unplugged refrigerator. Removed light bulb cover and ligt bulb. Unplugged and removed Ice maker and motor. Removed air duct cover from motor. Unplugged and removed evaporator housing and fan. Pulled fan blade off. Unscrewed brackets from fan motor, removed dust cap from top of motor and grommet from bottom. New motor came with 6 pin connector and four pins for evaporator fan motor. Cut the harness grommet to separate the light bulb wiring from the evaporator motor's. Pushed the the old light bulb pins (red and orange) from old connector and push them in to the new fan motor connector. Reversed the process and no more noise

Refrigerator was showing actual temperature of 80 deg, freezer was about 3 deg high. (house temp was 65 at the time) Defrost heater seemed like the only component able to heat that much, so the defrost thermostat seemed like the likely culprit. I followed the installation directions in the video, and the fridge has been fine ever since.

I took off the back panel in the freezer. Located the wires going to the old thermostat, cut them with wire cutters. I then spliced the matching wires together and attached the part to the coil tube (There is a little clip on the part, be sure to do this because I forgot and had to go back and do this again!!!).

All the rest of everyone's post are all what I did. The only other thing I recommend is to put the back panel over the evaporator coils when your done. I replaced defrost thermostat, and heater. Once I initially completed it it kept icing over more than usual. You have to put the back panel back on so airflow goes over the coils.

My Ge top freezer fefrigerator was going into defrost mode and the heater was staying on for too long causing the food to thaw and eventually refreeze. Originally thought it was the mother board but after researching and do some troubleshooting of my own I realized the defrost terminating thermostat was bad. $8 part from Parts Select. Accessed the evaporator by removing back wall plate. Located thermostat and cut two lead wires to it. Spliced in new thermostat and reattached to eveaporator. Refrigerator seems to be good as new. There is an installation video on the web page that shows you step by step proceedure.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Once the part was received, it was very easy to snap the new part into place, and reinstall the drawers. No tools were required to complete the repair.

Only problem we had was when we removed back wall on freezer the couls were totally iced up. After waiting for that to defrost. (3 HOURS) repair went fine. Was kind of hard to get to the part being its a side by side but happy with results

the parts I ordered did not fix the problem the problem was with repairman did not follow the instruction and cut jumper wire on main control board

Removed the back pannel from inside the freezer. Defrosted the ice build up. Removed the shroud from the back top of the freezer. ( This contains the fan and the light assembly). Removed the fan and replaced the motor. Cut the wire for the temperature sensor and wired in the new one. removed the defrost thermostat and replaced with the new one. Reassembled the unit and reinstalled it into the freezer compartment. replaced the pannel and plugged unit back in.

I was intimidated by this repair(as I am with most repairs), because there were 2 possible problems. But being able to purchase both parts for $30 (including shipping) made it worth a try. Thanks to the instructional videos that were sent, the repair was much easier than I anticipated. For me, the hardest part was fitting my shoulders in the narrow freezer. Now the appliance works like a charm. This would have been a $150-$200 repair had I called a company to do it.

I replace defroste thermostat :i defrost al the ice