CST24GRXAAA Hotpoint Refrigerator - Instructions

I removed the ice maker,removed the broken piece of the old light shield,screwed the new light shield in place,and replaced the ice maker.It took all of 5 minutes.

First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.

Opened, discovered not flapper but more complicated

This was a 15 year old great working GE regrigerator. Refrigerator was not cooling properly, though the freezer worked great. Using flashlight, examined cam riser which was clearly broken. YOU MUST ORDER TWO GASKETS AS BOTH WILL BE WORN. After removing all food from the door, taped plastic sheet over the open space to keep food somewhat cool Removed top hinge cover and screws on top of door and lifted door out of bottom bracket placing it flat on kitchen island. Unscrewed hinge elements including old broken cam and shims form the bottom of the door and fit in the new cam. Unfortunately one of the shims was broken, so I used a thin plastic black washer from the hardware store which was big enough to fit over the pin on the bottom of the refrigerator itself. Screwed all the parts back together. Be VERY careful to note how you removed them in the first place...mabe take a digital foto or two. This was kind of tricky to remember. Then used a hammer and chisel to break off the rivit holding the bottom hinge elements on the refrigerator. Sawing with jigsaw didn't work that well. The rivit came right off. Then used a flat head screw, lock washer and nut instead of a reivit and attached the new second cam riser. You are now done with the new parts. Simply reattached the door and it closed like new. Had a simultaneoius problem with a faulty defrost heater in the freezer which also had to be replaced and which was really easy to do. About an hour max. This was the real cause of the refrigerator not cooling properly. But that's another story.

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

I removed the plate covering the water valve for the ice maker and water dispenser, removed the nut holding the 5/16" tubing to the valve and took off the tubing and nut. I did not need to turn off the water supply or unplug the unit. I removed the kick panel in the bottom front of the refrigerator, replaced the existing plastic fitting with a new push-on fitting, then spliced the tubing coming from the water chiller to the valve where the leak was thus bypassing the broken tubing with new tubing. I reassembled the valve using the original plastic compression nut, replaced the cover and ran the water dispenser while checking for leaks. The water dispanser works great with no leaks.

BUY TWO CAMS! Just like the others, both of the cams were shot. My husband & I did this ourselves & have NEVER attempted appliance repair before.
We propped the door up high enough to access the bottom hinge piece on the fridge & removed using socket. Removed the cover from the top hinge. Slid door down off the top hinge in able to get to the cam on bottom of door. Replaced this cam 1st in order to get door back on while worked to get the old cam off hinge. As others posted, this is rivited on. Used grinder to grind off rivit & hammer & punch to punch out. Attached new cam with bolt & nut found in our tin of leftovers. Inserted hinge into door & reattached to fridge. DONE! Not hard at all & didn't even argue the whole time.

1. Put all perishable food into ice chest. Empty door shelves.
2. Remove top hinge cover with Philips screwdriver.
3. Supporting door, remove top hinge attached by two hex screws.
4. Lift door off bottom hinge.
5. On bottom of door, unscrew the hex screw holding the broken plastic cam.
6. Loosen the second hex screw enough to free the broken cam.
7. Replace the cam and tighten the hex screws making sure the opening of the cam lines up with the hole under the door.
8. Snap off plastic grill at the bottom of the refrigerator.
9. Remove bottom of the two hex screws holding the bottom hinge tot eh refrigerator body.
10. Loosen the second screw enought to rotate the hinge upsidedown. Tighten the screw again.
11. Now the rivet bottom is exposed so as to facilitate drilling it out to remove the broken cam.
12. Loosen the hex screw again and turn it back rightside up. Reinstall the bottom screw and tighten both of them.
13. Using an appropriate size bolt, lockwasher and nut, install other new cam.
14. Reinstall door reversing steps 1 to 4.
15. Don't forget to return the food to the 'fridge, by the way!

I was set to buy a new magnetic seal to hold the door closed, when I looked it up on PartSelect I saw the recommendation that the problem might be the door closing cam.. I check it with a mirror and sure enough the cam had broken and the door sagged about 1/4 inch. I then followed the instruction and removed the top hinge, lifted the door off and replaced the cam. I did need two and the one attached to the lower hinge had to be drilled out and a new screw and nut attached to hold the cam. It was simple to do, I would recommend selling the door closing cam be sold in pairs with a #10 1/2 inch long screw with lock nut.

Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.

First a big thank you to PartSelect.com. I read the stories posted by others before ordering the parts and found out that I probably needed 2 of these cams. So I followed the advice of others and ordered 2 cams. I'm really glad I did because once I got the door off I discovered both were broken up real bad. Maybe you guys should think about offering them as a set?
Anyway the repair was fairly easy, except for the bottom cam which was revited to the bottom bracket. Again, thanks to the other stories about repairs with this part I was already expecting this. So the repair went like this. I removed the door by unscrewing the hinge on top(1 screw and 2 bolts). Took the door off and laid it on its side. Removed the bottom bracket( 2 bolts). Used a drill to drill out the rivit. Used a spare screw/nut that I had in a tool box to fasten the cam to the bracket. Put it all back together and I was done. The biggest challenge was figuring our if I needed 2 cams,so with the advice of others on your site, my repair was a snap.

The old cam had broken and was on the floor. I ordered one new cam. I should have been told to order at least two, I did not know they worked in pairs. So I had to re-order, I ordersed four, I was able to see that the other (freezer door has cracked cams) door will soon need replacement of the cams. I had trouble installing the new part because the rivit also needed to ba replaced. I did a "Rube Goldgerg" to get the new part to sit properly. I drilled the hole open a little and forced the part into place. All is well. Thank you very much!

Same problems as already described .... door would not close, plastic bits on floor, angry, ready to throw-out 15 year old “dog” and blow at least $1,000 on a new appliance!

This repair is dead easy. Remove the two bolts holding the top hinge and lift off the entire door. Don’t be surprised if the original Riser Cam has virtually disintegrated, mine was a wreck. Remove two bolts that retain the old flat metal “shim” and fiber “gasket”.

Fit new Riser Cam and re-use old shim and gasket. Replace door on dome-shape bottom hinge mount and then re-fit top hinge.

If in any doubt order new shim and gasket along with the new cam riser. Or, do as I did, and “manufacture” either of these parts from scrap material found in the workshop ....

After reading the stories here, I purchased one door closing cam. After getting into the problem area, I realized I needed 2 cam, so I put the door back together and ordered another cam. If you have this problem, buy 2 cams.

First, I was glad I read other posts on this repair as I would have only purchased one of the replacement cams when I needed two! I removed the top door hinge with a screw driver (cover) and small socket set for the door hinge. I then removed the door and removed the bottom hinge (socket set). The bottom hinge had a small rivit that held the bottom cam in place. I used a hack saw to cut off the rivit and replace the cam and secured it with a small machine bolt and nut. I then laid the door on its side and removed the top am from a bracket attached to the bottom of the door. I relaced the cam (second one) and reinserted the screws. I reattached the bottom hinge and then placed the door on the bottom hinge pin. I then held the door in place while inserting the top hinge pin bracket into place and retightening the top screws. I replace the cover with a screw drive which was the ahrdest part in trying to find the hole the small screw gets inserted into. DONE!