CTX18BABLRWW Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dawn from Wilton, ME
- Parts Used:
- WR24X450
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door gasket had rotted on the bottom
Soaked the new gasket in warm/hot water and snapped it on without any hassels. Thank you also for the fast delivery!
Was this instruction helpful to you?
Thank you for voting!
Retainer strip for door bottom not available
We bought the side door retainer strip with the hope we could simply cut it to length and it would be the solution for the top/bottom retainer strip not available.. The problem was the holes for the flathead screws on the door bottom do not match the pattern of the holes on the side retainer. This meant we had to mark and drill new holes carefully on a drill press and then cut the piece to fit. After that it was no problem at all to screw it back to door and install the new gasket. Sure wish the top/bottom retainer strips were in stock somewhere.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Sumter, SC
- Parts Used:
- WR24X450
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Fresh Food Door Torn
My experience with PartSelect was excellent. My main concern was ordering the right gasket. First, I found the model number on the inside of the refrigerator. I ran model number on PartSelect and the compatible gasket came up. I removed old gasket carefully pulling it out. I cleaned around the groove that holds the gasket in and where the gasket lays. I boiled water and put it in a cake pan. I warmed up the gasket and smoothed and straighten it out. I started in each corner of the gasket and then worked from each corner pushing it carefully into the holding groove. Took me about 25-30 minutes. It seems to be working great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- theodore from salisbury, NC
- Parts Used:
- WR60X30349, WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
bad fan motor
take fan out,put new in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Owensboro, KY
- Parts Used:
- WR71X10080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Retainer Bar bend
Removed the bent bar and the end clips. Attached the end clips to the new retainer bar and snapped into place on the refigerator door. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Simpsonville, SC
- Parts Used:
- WR23X10725
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch quit working
removed the inside fridge electrical panel and swapped switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X10725
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Mount Nebo, WV
- Parts Used:
- WR07X10099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Warm air from freezer
Simple. Take off back panel, locate relay on side of compressor tank, remove, replace.... cold air. Unit would run, but only blow warm air. Relay will rattle when you shake it if it is bad. New relay makes no noise when shaken.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danelle from Williston, VT
- Parts Used:
- WR2X9144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
end caps were broken
Purchased new ones. Took out the old ones with a screwdriver and slid the new ones in. Had to repair small section of the skin with glue and white duc tape where one of the end caps had ripped through
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas j from jim thorpe, PA
- Parts Used:
- WR24X450
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
liquid in bottom of refrigerator
took door off removed old gasket which was the hardest part of whole job put new gasket in place pressed into grove and rehang door need something to hold door up in place to reattach.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Columbia, MO
- Parts Used:
- WR9X559
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Freezer worked, frig not cooling
First, read through blogs which said it could be something frozen up. I unplugged and let it warm for a few days. Didn't work. No ice found. Then, assumed to be thermostat. Unplug frig. One screw removes cover, then another 2 screws to take out thermostat compartment. Unplug wires from harness and remove. Simply put in the new thermo (reverse from removal), and reassemble. Bingo, nice and cool within 12 hr. Rock solid 35F ever since. Pretty simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from Baltimore, MD
- Parts Used:
- WR24X450
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
None
Remove old gasket clean area and install new gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X10725
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X10725
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X10725
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!