CSX22DME Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- vincent from mahwah, NJ
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
door was not closing properly
Your vidio was Brilliant !!i just followed your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nghia from San Jose, CA
- Parts Used:
- WR17X2740
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Replace Rusty Item
Before disassembling the parts need to replace, I use my digital camera to get all the different angle of the item so I have the full reference to asswmble the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carmine from Millington, NJ
- Parts Used:
- WR17X2740
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Replaced corroded auger
Removed front cover, removed rear cover careful to note position of spring assisted parts, used pliers to unscrew auger rod end cap, removed and soaked in Lime Away fixed and movable blades. Reassembled using diagram on website for guidance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from North Plainfield, NJ
- Parts Used:
- WR2X4901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Door Cam And Cam On Refridgerator Were Damaged
I did not realize I needed 2 cams to complete repair. Door cam was riveted in. I had to drill out rivet and replace with nut and bolt. Otherwise it went quite sommothly. At first I just replaced the cam on bottom of refridgerator but door was not quite right when closing. Further inspection showed the door had the other half of cam that also needed replacement. Needed 2 orders. Paid for 2 shippings.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucky from Dacula, GA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator door would not close.
1. I removed the top door hinge.
2. I removed the door and laid it flat.
3. I replaced the cam attached to the bottom of the door. This was very easy.
4. I removed the bottom door hinge and had to remove the brad that held the second cam. This went well as I was able to saw it with a hacksaw.
5. Replaced the second cam with a bolt and nut.
6. Replaced the door and top hinge.
7. Remember to order two cams when you do this repair.
2. I removed the door and laid it flat.
3. I replaced the cam attached to the bottom of the door. This was very easy.
4. I removed the bottom door hinge and had to remove the brad that held the second cam. This went well as I was able to saw it with a hacksaw.
5. Replaced the second cam with a bolt and nut.
6. Replaced the door and top hinge.
7. Remember to order two cams when you do this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Charlotte, NC
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door did not close automatically
Removed screws holding top door hinge. Lifted the door off bottom hinge. Unscrewed cam from bottom of door. Drilled out rivet holding the second cam in the bottom hinge. Replaced both cams using a flat headed bolt to hold the bottom cam. Dropped door into bottom hinge and replaced top hinge screws. Job done.
Make sure you buy two cams and have a bolt to replace the bottom rivet.
Not a difficult job as long as you have a drill !!!
Make sure you buy two cams and have a bolt to replace the bottom rivet.
Not a difficult job as long as you have a drill !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Upper Malboro, MD
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door would not shut by itself.
I followed the directions on the computer and everything went just as the video said it would. This was one of the easiest repairs I have ever done. Usually, it does not go as planned.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neal from Cleburne, TX
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door would not close properly
Removed the door and loosened the bottom bracket and scraped the old cam off. Mounted new cam and tightned the bracket. Replaced door and it was a total sucess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from NEWPORT, PA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Door would hang up half way closed
Replaced both upper and lower cam's. Removed door from refrigerator, removed bolts on door cam on bottom of main door and replaced cam, then removed bolts from door hinge assembly, drilled out rivet holding on cam, replaced with new cam and re-riveted.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Chesterfield, MI
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Refrigerator door would not close by itself - would stay open when you thought it was closed
1st: Order (2) closing cams! One for the hinge pin / bracket and one for the bottom of the door.
The closing cam on the door was where the Dremel type tool is required, since you have to grind the head off of a factory rivet.
I installed the cam with an aluminum pop rivet.
Next, remove the bracket on the bottom of the door with sockets and install the second closing cam.
Re-attach the top door hinge pin and align visually; tighen all bolts. Job finished, but more important , my wife is not nagging me about the repair that I put off for over a year!!!!
The closing cam on the door was where the Dremel type tool is required, since you have to grind the head off of a factory rivet.
I installed the cam with an aluminum pop rivet.
Next, remove the bracket on the bottom of the door with sockets and install the second closing cam.
Re-attach the top door hinge pin and align visually; tighen all bolts. Job finished, but more important , my wife is not nagging me about the repair that I put off for over a year!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from San Antonio, TX
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door would not stay open
Removed the top cover using a Phillips screw driver to access the top 2 screws holding the bracket. Once the bracket was removed, lifted the door off the bottom hinge. Replaced the door closing cam, replaced shims and screws. Placed the door back on the bottom hinge, inserted the top bracket and secured.
This was the ultimate resolution to the problem. The problem I encountered was getting all of the correct parts. It took me 3 tries to finally identify and receive the parts needed to make the repairs. Using Part Select made it easy because they had the parts I needed. My 3 tries were partly my error and does not reflect on Part Select. I would recommend others use Part Select when choosing their replacement parts.
This was the ultimate resolution to the problem. The problem I encountered was getting all of the correct parts. It took me 3 tries to finally identify and receive the parts needed to make the repairs. Using Part Select made it easy because they had the parts I needed. My 3 tries were partly my error and does not reflect on Part Select. I would recommend others use Part Select when choosing their replacement parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Darien, IL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Door won't close
This my second time to do it after 8 years. Took 10 minutes.
1 Remove all the contents on the side door
2 Remove the 2 bolts on top connecting the door to the refrigarator
3 Lift and remove the door up and put it the side
4 Clean and remove the old door closing cam put the new one
5 Door ref is fixed
1 Remove all the contents on the side door
2 Remove the 2 bolts on top connecting the door to the refrigarator
3 Lift and remove the door up and put it the side
4 Clean and remove the old door closing cam put the new one
5 Door ref is fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Burmingham, AL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Problem closing door, would not shut easily.
My wife and I gave an old, but really good refergerator to our son (a Major in the Army). Upon taking it into his house he had to remove the doors of the refergerator. While he put the doors he lost the "cam" for the door, making if difficult to close (actually had to lift the door up and then close it). I ordered the replacement part, and unless I am mistaken, it arrived the same day. I still cannot figure out how this happened, but it was great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Danville, VA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door dropped down and draging, would not close
Buy ( 2 ) cams !!!! removed hinge cover and hinge on top of the door, ( 2 screws )...lift door off of the bottom hinge and lay door on the floor, remove broken cam on bottom of door with nut driver, ( 2 screws ) , install new cam..... remove the bottom hinge off of the front of the refrigerator with nut driver, (2 screws ).... saw rivit off and remove old cam, install new cam and secure with new bolt and nut,... reinstall hinge back on bottom front of refigerator.....replace door back onto the bottom hinge.....install top hinge back onto the top of the door....replace hinge cover......done !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalie from Randallstown, MD
- Parts Used:
- WR17X2740
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
the auger was rusty, causing ice to have brown spots
Pay close attention to how you disassemble everything. You might even want to take a picture. I taped all the screws right where I unscrewed them, to make sure they were replaced in the right section. Also use the picture diagram that on the computer.
Was this instruction helpful to you?
Thank you for voting!