HTS22GBPCRWW Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Jamestown, ND
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Slide track on right side of chill tray, where it was held together, on the metal frame, the screw cracked the plastic.
Went to Sears, where I bought the Fridge, they could not locate the part I needed, so I went on line, and found partselect.com, entered the proper information, found the part I needed fast, ordered the part, received it in two days time, I already had the old part off, so it took less than ten minutes to replace it with the new part, works great, the people at partselect.com were great, an if needed, I will gladly order from them again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from Montebello, CA
- Parts Used:
- WR72X10073
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken slide pan lh
pull out the slide pan lh and replace for the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Brooksville, ME
- Parts Used:
- WR60X10257
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Fan motor was really loud and whining
Empty the contents of the freezer.Take out the one shelf.Remove the plastic pieces covering the fan and evaporator removing 2 screws with the nut driver.Remove the metal back using the nut driver(2 screws)Remove the fan assembly from the back of the freezer.(4 screws)Remove the green ground wire from the fan assembly(1 screw) Take the fan assembly out of the freezer and remove the old fan(2 screws) and reinstall the new fan.Assemble the parts in the reverse order .Very simple and intuitive for anyone who is "handy" at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Marquette, MI
- Parts Used:
- WR60X10257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
fan did not work
Removed plastic housing and metal back panel,then removed fan motor and reinstalled everything. In all it took about 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dayton, NV
- Parts Used:
- WR60X10257
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Made a lot of noise
Remove plastic parts then remove back panel, remove plastic seround holding motor, romove 2 screws holding motor bracket, unplug motor, reinstall motor, bracket, seround, back panel DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from N Ft Myers, FL
- Parts Used:
- WR60X10257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
needed new Evaporator Fan Motor
Follow the instructions on the video. Took pictures removing Evaporator Fan Motor. Installed new motor in 44 minutes. Thank you part Slect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from albany, NY
- Parts Used:
- WR23X10334, WR09X10104, WR02X11567, WR01X10220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
frig ran to often
took apart stat. area rplaced wire harness &t.stat simple but im a retired union electrican so wiring was a bit easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BLOOMINGTON, IN
- Parts Used:
- WR17X11970
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
There were no fasteners (like a screw) that could be unscrewed to remove and replace the center glide to the frame it hangs from
After removing all the parts, the bins and a large glass fitted shelf or lid, on top of the two crisper bins I then removed the whole frame the three glides are mounted to. The frame is molded into one large piece matching the whole horizontal space of the refrigerator, so it is wiggled loose from its space. I lifted out the whole thing and placed it on a surface on which I could work while see everything I was doing. With no screw (both top and bottom of the U-shaped gripper “clevis” end are solid) or other type fastener that could be removed I finally just pried the "clevis" of the center glide that grips the front of the frame. This clevis grips a set of small plastic studs that fit into matching round indentations in the top and bottom of the clevis jaws. It’s necessary to keep the stud from slipping back into the first indentation while opening up the other side of the jaw so that both are free at the same time and the clevis will slide sideways. Using a butter knife because it was a good fit and stiff enough, I released the top, and then the bottom using the knife to bend it a little bit. The clevis opens up just enough to allow the edge of the frame it’s gripping to be released from its grip. The new one is put back in exactly the same manner but in reverse. The opposite end from the clevis simply tilts up until it can be disengage and reengaged in the same manner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from vernon, AL
- Parts Used:
- WR50X10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
fridge stoped cooling
unplug fridge! removed ice maker. removed the back panel in frezer. I uncliped thermostat; cut wires on thermostat and installed new thermostat.
Was this instruction helpful to you?
Thank you for voting!