CSX19LABCWH Hotpoint Refrigerator - Instructions

they sell the cam piece but the instructions says not to replace only one part. so beware you need both the cam and hinge as a kit .

Discovered the door cam was broken. Did a search, found the part on PartSelect.com. Read the repair stories and realized I need two cams. So I just bought the whole hinge assembly figuring it would be a little easier and did not cost that much more.

Put blocks under the door, unbolted the old hinge from the refrig, and the old cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.

1. Blocked up the door keep it steadily and enable ease access to screws.
2. Removed screws holding the door closing cam and lower door attach bracket.
3. Disconnected clamp holding the water supply line for the water and ice dispenser and disconnected the water line at the joint.
4. Removed the broken cam and put the new one in it's place, threading the water supply line through the hole of the cam.
5. Put everything back together in reverse sequence of removal.

The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.

Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.

Easy job .. around 20 minutes.

I could see a broken part but couldn't tell exactly how it was oriented on the hinge. I bought just the cam riser but then thought I needed the hinge kit based on what I read on this site. Then I saw better pictures of the hinge kit on another site & realized there are 2 cam risers that meet. The one riveted to the hinge was fine (in my case) - I only needed the upper one...a very inexpensive repair. Do NOT remove the door for this repair. Slide the door up a bit while closed and use a pint-sized paint can to prop it up. Make the repair and remove the can...done.

Removed trim cap at top of door. Removed two hex head screws and lifted top hinge off door. Lifted door off lower hinge. Unscrewed broken cam riser from bottom of door and replaced with new part which was then screwed into place. Replaced door on lower hinge, Replaced upper hinge onto top of door, replaced screws and replaced trim.

Easy peasy. :-)

Use several wood blocks and propped fridge dooe up and someone else steadied the door while I replaced the hinge. Pretty easy.

1.Emptied the stuff from inside of the fridge door.
2.Using a phillips screw driver I removed the plastic cover over the top hinge.
3. Using a small ring spanner I removed the two bolts holding the top hinge (pin), removed the hinge and lifted the door off the bottom pin.
4.Using the same spanner I removed the bottom hinge containing the broken plastic cam.
5.Replaced the broken hinge with the new one and put a little grease on the hinge pin.
6.Placed the new plastic cam on the hinge pin and refitted the door.
7.Replaced the top hinge and plastic hinge cap, Job Done!

A couple of points a) When your plastic cam needs replacing, always buy the hinge pin & plastic cam. The pin has a plastic cam welded to it and as this is the partner of the plastic cam it will also be worn so you should replace them as a pair.
b) You will spend more time cleaning the 'out of the way' parts of the fridge than actually carrying out the repair.

My fridge is now as good as new.

First I bought the right tool to remove the hinges.
Then replaced the hinge with the two cams.
Now the door closes itself.

Emptied glass shelf, removed , removed old rail. Put new rail in with original screws ,then glass shelf. Done

blocked up refrigerator door.removed old hinge, and put new one on,with socket set.

It was really easy for me....my son told me what part I needed. I ordered it, and he installed it!

Removed top hinge assembly to pull door away from bottom hinge (2x hex bolts) Discovered that the pin on the bottom assembly had broken off. Removed and replaced bottom hinge assembly (2x hex bolts). Aligned door with top and bottom hinge pins. Tightened all hex bolts. Done

I followed the many post on replacing this part and everything went well. I had a little trouble getting the hinge post into the new hinge assembly, but with a slight adjustment it fell into place. I checked to see what tools I would need to do the job and had them ready before I even started. I removed the door and had it back on in maybe 10 minutes and I am not exactly Mr. Fix It. The only advice I can add to what everyone else has said is you should look the job over a little before you take the door off and have your tools ready. Then you won't have the door off for too long. I'd like to thank this site and everyone who gave advice on how to fix this problem. It made the whole job very easy.

This is a side-by-side unit. After blocking up the closed refrigerator door to the correct height to match the freezer door, I removed the lower hinge pin assembly by taking out two bolts. Save the shims (my had two) for the new hinge pin. Then remove the cam riser from the bottom of the door by taking out two bolts. Install the new cam riser on the bottom on the door. Then install the new hinge pin assembly. Total time 15 minutes.