HPS18BTNFRWW Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cyndy from Rancho Cucamonga, CA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I dropped one of the trays and it hit the light switch and broke off!
It was so darn easy! Took less then 10 minutes to fix. Self explanatory no instructions needed! Very cool!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from COLUMBUS, OH
- Parts Used:
- WR17X30024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Attached to hooks
Attaches to hooks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felina from BRONX, NY
- Parts Used:
- WR17X30024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
It was broken
Just take out the old one and put the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rafal from FSTRVL TRVOSE, PA
- Parts Used:
- WR55X31113
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Freezer freezer up warm temperature in the refrigerator
This is the symptoms you have when your defroster with timer goes bad. Warm refrigerator, frozen freezer. The pants of the model of the refrigerator. There is some screws to be removed from the back panel to access to the heating coils. Make sure that the coils are defrosted, so can easy access to the heating element. You will have to unscrew hitting element out of the wall without breaking or bending the lines and gentle, remove any pens or connections on a side, and underneath to remove the heating coil harness it’s attached around very easy install putting back the same way, it should not even not experience person. It should not exceed more than half an hour. Common sense and a very important make sure all power has been disconnected before you start working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pat from ERIE, CO
- Parts Used:
- WR23X31507
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior light door switch broken when jar fell off shelve and hit switch
Very easy with small screw driver . Carefully pry broken switch out pull off two connectors install new switch connect as before . Unplug refer 1st . Works great . Refrigerator will not work with bad switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evelyn from ALTON, MO
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light switch wouldn't turn on inside light
I used the pliers to hold switch while I got screwdriver under the switch then pulled out. I THEN unplugged old one and plugged in New one and put it back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from GREENSBORO, NC
- Parts Used:
- WR02X12008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fan was not centered in the middle of the back panel opening.
Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from san francisco, CA
- Parts Used:
- WR32X21260
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Shelf broke while it was being cleaned.
Just put one end in its slot and that was that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from VALLEY CENTER, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Loud whirling noises when the motor started up, then they subside (and stop) in a short time
I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BOZEMAN, MT
- Parts Used:
- WR02X12008, WR02X10540
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy Freezer Evaporator
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from PALMYRA, VA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The switch was loose ( no spring). The lights did not work.
Unplug the refrigerator. Gently pry old switch out with screw driver. Move wires to connector on new switch with needle nose pliers. Pop it back into the hole. Plug back in. Peek inside to see the lights working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Escondido, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Fan making noise.
Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEW YORK, NY
- Parts Used:
- WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
noisy refrigerator
I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from N LAS VEGAS, NV
- Parts Used:
- WR32X21260
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke the glass on shelf
Just replaced the glass, easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharri from Charlotte, NC
- Parts Used:
- WR23X31507
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Child Broke Light Switch Inside Refrigerator
Pulled out broken switch with flat head screwdriver and replaced with replacement part purchased from partselect. Easily plugged in new part and replaced.
Was this instruction helpful to you?
Thank you for voting!