HPS16BTNHLWW Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MaryLou from Levittown, NY
- Parts Used:
- WR60X10207
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Noise in the back of freezer
I must thank yo for sending the fan so fast. If I ever have to deal with any appliance again, you are first on my list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from PALMYRA, VA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The switch was loose ( no spring). The lights did not work.
Unplug the refrigerator. Gently pry old switch out with screw driver. Move wires to connector on new switch with needle nose pliers. Pop it back into the hole. Plug back in. Peek inside to see the lights working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from GAINESVILLE, FL
- Parts Used:
- WR60X31522
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Noisy fan in freezer compartment
First I unplugged the power. Then I removed the wire shelf, center plastic cover, flited the stryofoam piece out, removed the back panel. Then I disconnedted the fan connectors. Then I took the fan brackets off and removed the clamp holding the fan blades to the motor shaft. I then reversed the steps to complete the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from LYNCHBURG, VA
- Parts Used:
- WR60X31522
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Refigerator was amking a loud noise when the fan came on to cool.
Followed the on line instructions and found the repair to be very easy. Took longer to remove the food from the freezer than to switch out the fan motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from NEW YORK, NY
- Parts Used:
- WR60X31522
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy motor that was getting worse.
Followed the steps on the linked video. Absolutely accurate and easy to follow. Beware: Don't drop a screw down the opening after removing the styrofoam block.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from san francisco, CA
- Parts Used:
- WR32X21260
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Shelf broke while it was being cleaned.
Just put one end in its slot and that was that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from CHAMBERSBURG, PA
- Parts Used:
- WR60X31522, WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fan became noisy
First unplug freezer and empty contents, then remove the screws from the air deflector, carefully remove styrafoam air deflector block then remove back panel for easy access. Fan will be easy to switch out from there. I highly recommend the You Tube video which is where I got my basic instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BOZEMAN, MT
- Parts Used:
- WR02X12008, WR02X10540
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy Freezer Evaporator
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEW YORK, NY
- Parts Used:
- WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
noisy refrigerator
I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Escondido, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Fan making noise.
Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felina from BRONX, NY
- Parts Used:
- WR17X30024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
It was broken
Just take out the old one and put the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from COLUMBUS, OH
- Parts Used:
- WR17X30024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Attached to hooks
Attaches to hooks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from GREENSBORO, NC
- Parts Used:
- WR02X12008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fan was not centered in the middle of the back panel opening.
Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy m from BROWNINGTON, VT
- Parts Used:
- WR60X31522
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
freezer was too warm, only froze ice cubes on the bottom, fan making noise, food only stayed froze if already frozen
followed instructions in the video. simple tools. pretty easy. Most people would have just bought another refrigerator, $50.00 was much better. Is working just like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert from LOUISVILLE, KY
- Parts Used:
- WR60X31522
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Evaporator motor bearings failing - squeaking
1. Watch the video.2.Place all screws in a central location that will not be hit, stepped on, fall on the floor, etc. 3. Be systematic. 4. Allow a full hour. 5. Watch the video.
Was this instruction helpful to you?
Thank you for voting!