CTF14AGR Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert L. from Eldred, PA
- Parts Used:
- WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy fan
Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from St Johns, FL
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
water leaking on floor from ice maker valve
Replaced single outlet valve for the ice maker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Fair Haven, MI
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Frozen and split water valve
Hi, My furnace when out when I was away, frozen water lines were repaired, but my ice maker line was turned off, the valve split open. Summer is coming I want ice! I found the right replacement, ordered it, watched the free video, did the repair. It was so easy. And I saved an expensive service call. I am drinking a soda with ice from the ice maker as I type this! Thanks for solving my problem, I will be back next time something needs a part! Bob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Santa Teresa, NM
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench set
no water going to icemaker. Checked everything.
I first disconnected the plug from the wall outlet. I then turned off the water supply to the back of the refrigerator. I then disconnected the two lines to the water inlet valve and removed the nut that holds the bracket to the refrigerator. I removed the water valve and installed the new one the same way in about 5-10 minutes. It was very easy, but, unfortunely that was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kirk from dayton, OH
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice maker was not gettin water
took water line loose at outlet valve to confirm that water was getting to valve. I ordered part and it arrived the next day. It was very simple installation took 10 minutes. Thanks to parts select, Kirk
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlin from Willits, CA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
ice maker wasn't working
removed old valve, installed the new one. ice maker back to making ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Atlanta, GA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was not getting water
Ordered the part from "parts select". Removed old part, installed new part by unscrewing the old switch, simply cutting supply hose ...pluging in the new part and re-attaching water supply line. 10 minutes at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph Q from Independence, MO
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Replaced valve to ice maker
had to replace copper water line to valve
Was this instruction helpful to you?
Thank you for voting!