CSE22DRAWH Hotpoint Refrigerator - Instructions

Took door off. Replaced two cams at bottom of door, referencing those on the bottom of the freezer door. Also followed a video on the net. Worked like a jewel!

remove ice bucket and replace broken augar

I watched the video on the webpage and did as he did. it was quick and easy. didn't realize the importance of this little part until it broke

1. Watched the video on how to make the repair. 2. Used the tools recommended. 3. Followed easy instructions as demonstrated on video, and Viola! It was repaired.

Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.

Ther was a video on how to repalce this part on your web site. Describing what tools were needed saved me running back and forth to my tool box. I followed the directions given in the video and repair was completed in 1/2 hour. That included meremoving then cleaning and replacing the sheves in the door. And by the way, the part was shipped the same day I ordered it and arrived on my doorstep noon the following day.

I ordered a cam riser for the refrigerator door. I watched the "how to" video the day I ordered the part. It took about a week to get the part, but I was ready when it arrived. The 'how to' video was a big help. It showed me how to take off the door and replace the part. The process was quite simple! Oh! Don't forget to turn the refrigerator on again!

Part was received quickly and quickly installed-Thank you

Empty door first then take a phillip heads screw driver and unscrewed the top hinge cover 1 screw. Then used 5/16 nut driver to loosen top hinge from fridge. remove door by lifting and then lay on table to replace the lower washer that is held in by 2 screws and you only need to loosen one all the way leaving one in to align then replace and tighten it up your done.

replaced the ice buck, not difficult at all thanks for having it.

I followed your terrific video. I first got all tools ready, covered a table in cardboard, and removed food from the fridge door. I removed the cap and screws on top of the door hinge. Lifting the door off was simple, and after laying the door on the table, the retaining screw was easily loosened, and the cam screw removed. The only problem was that half the thin gasket under the broken cam was missing. No new gasket came with the part. I wanted the new cam to lay flat, so I made a partial gasket from a matchbook cover and filled the gap. It all went back together quickly. Just have tools ready beforehand. Ten minute job, unless you have to make a new gasket or part of one. Thanks, guys.

Using the #2 Phillips screwdriver I removed the top hinge cover from the top of the freezer door. Next I used the 5/16 nut driver to remove the 2 bolts holding the top hinge in place. Once it was removed I was able to lift the door off the bottom hinge. Placing the door on a flat work surface I loosened the bottom bolt holding the cam in place. I next removed the bolt holding the hinge in place. I was then able to remove the broken cam and replace it with the new one. I then replaced the bottom bolt making sure the hole for the cam and the hole for the hinge are lined up. I then tightened the bottom hinge bolts. I carefully placed the door back on the bottom hinge and put the top hinge back on.

I removed the old ice bucket assembly and used a screwdriver to remove the front panel (4 screws ) and installed it on the new ice bucket assembly, this took only a couple minutes and I inserted the part back into the freezer and that was it. By the way, I'm a 70 year old female.

Bought a new Ice Bucket and Auger assembly and replaced the existing unit. Had to remove 4 Phillips head screws, remove and replace front panel and put bucket back in the fridge. (The bucket just drops in place in the freezer) and works perfect!!

Ordering the complete Auger Assembly made it real easy. I only had to unscrew the ice maker door and re-attach it to the new Assembly. It took me longer to write this than to reassemble and re-install.