CSX22DMD Hotpoint Refrigerator - Instructions

First I took everything out of the fresh food door, then I removed the top hinge cover using a philips head screwdriver, and a nutdriver for the two screws holding the upper hinge. Lifted the door off the bottom pin, and placed it on the floor. Then took off the bottom hinge and used the Dremel tool to grind off the rivet holding the broken door cam on the bottom hinge. Used a nut and bolt to hold the new cam in place, and put the lower hinge back on. Then replaced the other cam on the bottom of the door itself, using the nutdriver. (Be sure to buy two cams, and have the bolt and nut to replace the rivet). Reinstalled the bottom hinge, put the door on, replaced the top hinge, and presto! Works great! Thanks to the others on this site for their stories - really helped make it an easy and quick repair!

First we removed the door. Then we had to hammer the old part off including the old rivot. We fould a screw that fit and put this piece on. We held the door in place and screwed the hinge on the main unit.

Ordered at PartSelect and received the auger and blade within days. Printed the parts diagram and proceeded to take the auger apart the time it took would have been much less but I seized the opportunity to do a deep cleaning of the old parts before replacing them....The part diagram was the key to simplicity and the fast shipping was awesome. Thanks I'll be back....

First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.

Let me start by saying, I usually hire something like this out but figured I would give it a try. The install was fairly straight forward, however it would’ve been nice if the instructions would have been more useful. Instructing me to remove one screw to release the auger and solenoid enclosure wouldve been nice. There were 3 other screws that I didn’t need to remove and they were the ones holding the auger in place, which made assembling that much more difficult. Once to enclosure was removed, and the solenoid was exposed, it was a seemless process. I would however, recommend paying attention to or taking a picture of the connections on the solenoid. I was lucky to remember or got lucky. Regardless, I was able to complete the project successfully. If I had to do it again, I believe it can be done in 30 minutes or less.

The repair went well could have completed the job in 20 minutes if I had a selection of small nuts and bolts to replace the rivet that had to be drilled out. Also buy 2 of the door closing cams Part # PS297995 one goes on the bottom hinge of the refrigerator door the other on the bottom of the refrigerator.

Read the how to's AFTER ordering the part. 2 things....1) I wish I had read the comments first and 2) it was much easier than the comments led me to believe.

Had I read the comments first, I would have known to order BOTH the upper and lower cam....though there not a problem with the operation of the door. It would just have been a tad better if I had both. I'm not wanting to have to pay shipping for an additional part when the door works satisfactorily as it is.

As to the comments on how to do it....I took none of them. I (instead) removed the top hinge, and lifted to door off. I did have to have assistance to get the hole in the door aligned with the post, but that was rather easily done.

Would I do it again.....in a heart beat. I feel that I've save on the repair man making a call at the house, and experience has had me charged $60-$100 for virtually the same amount of service. My cost...shipping and all was under $20.00

First i removed the lower cover below doors . Then placed a 4x4 under the door to be fixed to keep it in place. Removed screws from hinge support on unit to remove cam Removed outside screw on door and loosened other to allow other cam to be removed . Always buy two cams if one is broken the other cant be in very good shape .The door will work like new with two .

At first, I noticed the refrigerator door didn't close at the same level of the freezer door. I started to adjust the hinges and noticed a chewed up black 'washer' at the base of the door hinge. Ppartselect.com was awesome, in that I easily found the schematic of my fridge, and the part I needed. Ordering was a snap, and it came to the house pretty quickly.
Installation, first raise the door up as high as you can, then scotch it with wood blocks (closed door). This takes the pressure off the bottom hinge you must remove.
Taking the hinge off is a snap, but then the problem presented itself. The old door closing cam was riveted to the hinge. I couldn’t get the old one off! I ended up taking it to the garage and breaking out the Dremmel tool with the abrasive cutter (the one that will cut through nails. I ended up cutting off the rivet. This was a pain.
I then found a small nut/bolt and put the new piece on, then put it back into place and removed the blocks. Works good as new. The toughest part by far was getting the old cam off… but there may be some easier way to get the rivet out that I’m not aware of.
Good luck.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

I placed books under the door until I had enough to hold the door up about 1/2 inch higher then when it is closed. The books and the magnetic gasket will hold the door, JUST DON'T TRY TO OPEN IT TILL YOU'RE THROUGH. That's about how high the cams lift the door when opened. I removed the two screws holding the door stop. Then removed the two screws holding the lower hinge pin.

It takes two of the cams

and the bottom one is riveted to the hinge. I used a grinder to grind the rivet so I could tap the pin out holding the cam. Put the new cam on and put the pin back in. I didn't put a new rivet, just gravity should hold it. I put the second cam on the hinge pin and one of the screws on the door stop holds it in place after you slide the hinge pin back into the door and replace the screws in the bracket then the door stop.
Make sure your lower door gasket didn't get damaged while the cams weren't working because the door wasn't being lifted up when opened.

First a big thank you to PartSelect.com. I read the stories posted by others before ordering the parts and found out that I probably needed 2 of these cams. So I followed the advice of others and ordered 2 cams. I'm really glad I did because once I got the door off I discovered both were broken up real bad. Maybe you guys should think about offering them as a set?
Anyway the repair was fairly easy, except for the bottom cam which was revited to the bottom bracket. Again, thanks to the other stories about repairs with this part I was already expecting this. So the repair went like this. I removed the door by unscrewing the hinge on top(1 screw and 2 bolts). Took the door off and laid it on its side. Removed the bottom bracket( 2 bolts). Used a drill to drill out the rivit. Used a spare screw/nut that I had in a tool box to fasten the cam to the bracket. Put it all back together and I was done. The biggest challenge was figuring our if I needed 2 cams,so with the advice of others on your site, my repair was a snap.

Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.

I blocked the door up with one 2X4 Then removed the lower hinge, installed the closing cam. Then I found that I needed one more closing cam that I didn't order the first time. This other one mounts to the lower section of the door and both cams set together. Re-ordered another cam. When it came in I installed it. Between ordering both parts I had them both in three days. The best to Parts Select
I now know where to buy my parts if needed again.

Thanks
Bob
Sandusky, Ohio

Same problems as already described .... door would not close, plastic bits on floor, angry, ready to throw-out 15 year old “dog” and blow at least $1,000 on a new appliance!

This repair is dead easy. Remove the two bolts holding the top hinge and lift off the entire door. Don’t be surprised if the original Riser Cam has virtually disintegrated, mine was a wreck. Remove two bolts that retain the old flat metal “shim” and fiber “gasket”.

Fit new Riser Cam and re-use old shim and gasket. Replace door on dome-shape bottom hinge mount and then re-fit top hinge.

If in any doubt order new shim and gasket along with the new cam riser. Or, do as I did, and “manufacture” either of these parts from scrap material found in the workshop ....