CTF14CRC Hotpoint Refrigerator - Instructions

It was way to ez to install only a couple of minutes that's it

Removed the broken fan blade (just pulled off) and replaced with part purchased PartSelect. Very easy repair, no tools required.

took a little more effort than the video show to remove old module and replace new. Works fine now.

I ordered four leveling jacks from this site for the refrigerator using a slightly different model number (my model was not listed). I assumed that the jacks all had the same shaft diameter and thread size. However, it turned out that the two front jacks had half-inch shaft diameters. It could be that originally there were rollers in front. The two rear jacks had quarter-inch shafts with "feet" for supporting them on the floor. So, I had to return the four jacks I had ordered and find another solution. I found two half-inch threaded bolts at the local hardware store that fit the front holes perfectly. I purchased 3.5 inch bolts to give me enough room to find the proper adjustment. I used wooden blocks and a crow bar to raise one side of the refrigerator high enough to screw in the leveling jacks. I used an adjustable crescent wrench to turn the bolts' hex heads until they were the proper height. I used the two original quarter-inch jacks in the rear holes and adjusted them to the proper height to level the refrigerator on the concrete floor where it is located. Then I removed the wooden blocks and tested to make sure the refrigerator did not wobble. I found that using the two bolts (no leveling jacks for the front holes could be found) for the front jacks proved to be the ideal solution. The job took me about thirty minutes, including the time it took to move the refrigerator into its final location and adjust the leveling jacks once more to create a solid stance so that the refrigerator did not wobble. While I had the refrigerator away from the wall, I removed the rear panel and cleaned the blades of the cooler fan and removed dust and dirt build up near the compressor with a vacuum cleaner. Then, I screwed the panel back into position, moved the refrigerator into its final place in a corner of the garage and made sure there was enough air space around it to allow for proper air circulation. This took me about twenty more minutes. I plugged it back in and listened to it come alive again. It is old but has never needed a repair and keeps everything cooled or frozen. I would suggest using threaded hex-head bolts in place of original leveling jacks if they cannot be obtained. Problem solved.

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

I removed the taped on bottle bar, attached the end cap on the right side of the bottle bar and reinserted the end cap tabs into the refrigerator door receptacle.
The refrigerator is 25 years old and I was surprised to find the part available. Thank you, PART SELECT.com

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

per your instructions

Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple

I removed the back of the refrigerator access panel disconnecte the 3 bolst holding the motor to the fan shroud assembly and removed the burned wires from the recepticle end at the wring harness. The fan motor comes with wire nuts but I chose to use the same style of connector as came with the OEM motor. I purchased the new connectors from NAPA and they are an exact fit. The new motor fit perfectly and has run flawlessly since the installation. It is in an awkward location and that takes time to get yourself into position but once there the assembly is very simple and it is rewarding to be able to use the appliance again. The ordering from the website and phone order are very easy to do and you have what you need in a timely and expeditious manner.

repalaced the old one with the new one. easy

take fan out,put new in

Defrost timer is hidden in the control panel in the refrigerator top middle. Turn to off and remove two screws which are hidden behind white tabs. I had to pry the old timer from the plug with a screw driver because it was tight. Try not to short across the terminals. Plug in the new timer. Replace it in the clip where you got old one and reinstall the controls. The freezer was still all frosted up so I had to remove the cover and defrost it with a hair dryer to get it to work. Then I turned it on and it works great.

Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.