CSX22DHE Hotpoint Refrigerator - Instructions

The plastic door closing cams had broken after 17 years of use. It was tricky figuring out how the new cams fit as the old ones had disintegrated. Also you need 2 cams - not one. I first ordered only one. A detailed parts diagram would have helped. First unscrew the top door mount cover and then the top door mount. The fridge door then lifts up and off the lower door mount. Next is the hardest part - drilling off the old pop rivet which held the lower cam. The lower door mount had to be removed to get at the underneath of the pop rivet, and a bench vise was handy to hold it as I drilled off the old rivet. Then you need small stainless steel nut and bolt and split washer or lock nut to replace the rivet. Next unscrew the old upper cam from the underneath of the fridge door and replace. The large hole in the cam goes through the door hinge pins. The two plastic cams should interlock in a way that makes the door swing close. Anyway, now the door works fine.

Removed door off hinge , remove bottom hinge, drill out rivet, lift off old cam & replace with new cam ,add new 1/4' BOLT(NOT SUPPLIED) to location where rivet was, reinstall bottom hinge & door ,check alignment, works perfect.

Thanks

Placed blocks under the refrigerator door to take weight off the lower hinge pin. Removed the hinge by removing two screws into the refrigerator and two screws into the bottom of the door itself. This allows the hinge to be removed so the old nylon "closer" pieces can be removed (the one attached to the refrigerator has a rivet holding it in place so that has to be drilled out and replaced with a 3/16 inch bolt and nut). After re-attaching the nylon "closer" to the refrigerator side of the hinge and placing all the shims back in place, I re-attached the hinge to the door first, then the half hinge to the refrigerator. Had to line up the holes, tighten the screws and presto, the door closes like it was new again.

The freezer door side is more difficult as there are wires and a water line to work around.

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

1. Put all perishable food into ice chest. Empty door shelves.
2. Remove top hinge cover with Philips screwdriver.
3. Supporting door, remove top hinge attached by two hex screws.
4. Lift door off bottom hinge.
5. On bottom of door, unscrew the hex screw holding the broken plastic cam.
6. Loosen the second hex screw enough to free the broken cam.
7. Replace the cam and tighten the hex screws making sure the opening of the cam lines up with the hole under the door.
8. Snap off plastic grill at the bottom of the refrigerator.
9. Remove bottom of the two hex screws holding the bottom hinge tot eh refrigerator body.
10. Loosen the second screw enought to rotate the hinge upsidedown. Tighten the screw again.
11. Now the rivet bottom is exposed so as to facilitate drilling it out to remove the broken cam.
12. Loosen the hex screw again and turn it back rightside up. Reinstall the bottom screw and tighten both of them.
13. Using an appropriate size bolt, lockwasher and nut, install other new cam.
14. Reinstall door reversing steps 1 to 4.
15. Don't forget to return the food to the 'fridge, by the way!

Easy

Please note that I did this repair 2 times before and it was very easy, it took me longer to get the stuff out of the refrigerator door.

But this time the existing upper and lower cams broke, and the lower part of the door was making contact with the screw that holds the lower cam to the lower support bracket damaging the head of the screw.

Now I could not use a screw driver and I had to use a wrench and a vise grip to hold the round screw head (not easy), and then replace the screw and nut.

I had to insert 2 flat washers under the lower support, to separate the door an additional 1/32 from the ref. base to accomodate the fact that the door gasket had lost its regular shape in the lower part of the door (I discover this when I dismounted the door).

Then I removed the damaged cams, replace them with the new ones and now it is working ok.

Manny

I learned from previous descriptions. Most important is there are two cams so order two. Second is that the door can be blocked from the bottom so the door doesn't have to be unloaded if you are careful. Remove the vent cover. Raise the door as high as possible while closed then block it from dropping down. I used wooden blocks. Remove the lower hinge and bracket on the bottom of the door. Put everythng back and you're back in business. A kit with both cams, spacers, and screws with diagram would have been nice to have.

I replaced both the punp and water line. the website depicting the repair parts was the best i ever worked with. The parts were high quality delivered on time and easy to install. Total job cost $30 as opposed the cost of of a service man or a new refrig.

Watched the video very good. Thank You

I used a block of wood to hold up the door. Then unbolted the lower hinge from the fridge. That is when I found out that it was fine and it was the upper half of the hinge that was broken (worn).
So I unbolted the upper hinge (mounted on the bottom of door) It uses the same part. So I installed the part on the upper half of the hinge.

I wish somebody would have told me that you need 2 of these for each hinge. The bottom one was in good shape, lucky for me.

There was what seemed to be a half chewed up washer under the refig. door. The door wasn't closing all the way. DING!! Something was wrong!!

I looked up your schematic for the refrig door and decided what piece might have broken. It was a good guess and the part showed up a few days later.

I wedged up the refrig door to take the tension off the lower bracket. Then, just took off the bracket and replaced the broken door closing cam.

Thanks to the stories on PartSelect my wife and I knew what to expect. The biggest hassle was sawing off the rivet that's on the hinge on the refrigerator (my wife volunteered for that job). When we got everything back together the door worked a lot better, but still wouldn't close without a little push. In frustration and running out of time, we put the stuff back inside the refrigerator door and that did the trick! The weight was enough to allow the door to close on its own.

completely removed door, then replaced worn-out cam on bottom of door-simple enough; then removed hinge from bottom of refrigerator; removing old cam required drilling out the rivet that fastened cam to hinge; secured new cam to hinge with small machine screw and nut. This procedure is relatively easy but does require minor mechanical ability and having a small drill and bit set. However, replacing the two cams totally fixed the problem.

i'm glad I read this forum before ordering the part because you need two of the door cams. They're sandwiched together on the lower hinge.

I removed the top door hinge, lifted the door off from the lower hinge and layed it on the counter.

I then removed the lower hinge using a nut driver.
I had to grind the rivot head off that holds the door cam onto the hinge and use a nut & bolt to replace
the rivot.