CTX18LYZLRWH Hotpoint Refrigerator - Instructions

Unplugged refrigerator.Checked that new gasket was the right size for freezer.Opened freezer door and lifted inside edge to access screw's. Loosened top screw's and screw's half way down each side and pulled gasket out. Installed new gasket into slot where old gasket was and tightened screw's across top and the first couple down side's.Lifted edge of old gasket and loosened screw's holding remainder of old gasket in place and finished removing old gasket.Finished putting new gasket in slot and tightened remaining screw's. The reason for only doing gasket half at a time is to keep the door square and not getting out of shape. If new gasket is warped when removed from shiping box run under hot water or soak in hot water until more flexible.

Pulled out the control sensor on the ceiling of the fridge. (2 screws) Took a picture with phone on how everything was installed. Unplugged all wires and pulled out Control Temp sensor. Installed new one and attached all wires. Installed back in fridge and plugged it back in. Everything works like new.

Simple install. .

Referenced a couple of videos first, held up the new gasket to ensure fit, then carefully pulled the old gasket off by hand. Wiped down the ridges/edges of the door, then installed new gasket first on opposite corners then along all sides. Simply pressed in to the door ridges/bracket. Used a putty knife to ensure the edge of gasket was not folded under itself, and the blunt edge of the handle to ensure it was snugly installed all the way around. Didn’t have to remove the door as I had expected to. Very easy and took maybe 30 mins.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

1. Disconnected 120 VAC power supply from refrigerator. 2. Removed 2 philip screws from horizonal panel containing the thermostat. (Panel is in refrigerator section). 3. Removed plug module from panel which freed the panel which allowed me to remove panel to do repair. 4. Removed wires from thermostat (cold control), and mechanically removed thermostat from panel and installed new cold control (thermostat). Replaced wires on control. 5. Replaced panel and reinstalled 2 philips screws. 6. time to repair about 15 minutes.

First unplugged frig. Took off cover to fan, then bottom & back panels in freezer. Unplugged the fan to the wires & marked them so we would know how they went back. Unscrewed the frame that holds the fan, laid the old one next to the new one so we could tell how it went. Only took a few minutes to do this, then put it back in the same way we took it out. Plugged frig. back in & it took off. Very happy with this. Runs like a new one.

i have a friend that had a big side by side refrigerator . he had repair man after repairman come and look at it. one thought it was the overload relay in the back and another just said it was compressor problems. this went on for over a month. after all of this and no one able to fix it he went and got another refrigerator . being the tinker with stuff kind of person i am i said i will come and get the old one to keep him from having to haul it off (he agreed). well i did my home work and tried a few things messing with it. tapping on the thermistat resetting the defrost timer and it dawned on me that that the fridge would run great if i wiggle a wire on the thermistat and reset the defrost timer. so i get on the internet look around for the parts. come to find out they were realy cheap. the day they get here i break out with a screw driver and a nut driver and take the cover off. i take the old parts out and put the new ones in in about 15 minutes. i wiped the inside of the frige clean and pluged it back in. well in no time flat this thing was cooling like a northern blowing through in january. then it dawned on me that i have a 27 cubic ft frige that i didnt pay any thing for (well the 65 bucks i spent on the parts) and it runs great. what a deal.

after getting the big side by side fixed up and running like a champ i realized i have a refrigerator in the garage that my parents gave me a couple of years ago that only ran for a couple of months. well i get brave and decide to try my luck with the second one. due to it sitting up for so long and the humidity i had to do a little more work to it. i replaced a few wires, changed out a couple of connections, put a thermistat , a defrost timer and a evapmotor in it this thing also ran like a champ. i cleaned it up real good ran some steel wool over the outside and sprayed a couple of coats of enamel on it and it looks brand new.

so to end this story i spent about 140 bucks and i have two refrigerators a big side by side ice and water despensing refrigerator in the house and a 17 cubic ft refrigerator in the garage (the wife was happy simply because i had a place to put beer and bait).

if i would have went and purchased both of these refrigerators i would have spent about $1400 for the side by side and about $450 for the other one. man what a bargin, so from now on even if it seems a little dificult i dont get rid of any thing until i give it a good look over and see if i can fix it. i saved a total of $1700 (minus tax).

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

At this time of the year our beach fridge is always full of food and drinks. Every time we want something it meant leaving the door open for extended time whlie moving things left, right and center. When the new shelf arrived I removed the food and drinks from the existing two shelves and moved them closer together. I then slipped in the new shelf and reloaded the food. Suffice to say the fridge stays open less and we are able to get at things without moving others. I wish I had thought to do this before.

Removed plastic covers and used a nut driver to remove the two screws that held the heater assembly to the freezer coils, disconnected wires from old assembly, connected wires to new assembly, replaced mounting screws and replaced plastic covers and secured them with the original screws. All in all, a fairly easy operation.

Went on YouTube and it had excellent instructions for removal and installation

After reading the trouble shooting section of the owners manual, I determined, without much difficulty, that the temp control was defective. I checked some local outlets and found the prices running from $36.00 and up. The same part from this site was around $20.00. Guess where I bought mine! It arrived in a timely fashion, and I installed it with no problem, in about 10 - 15 minutes. This was a very easy job, just remove and replace three wires snap the unit into place, and screw the cover on. Tip: I always use you tube or another source to get some instruction, just in case I'm not as smart as I think I am!

Well, when I opened the package the gasket was bended in half so I opened it and put it first on the floor and after some minutes I put it on the refrigerator side.
Then I took a screwdriver and easily removed the old gasket, cleaned the the channel where the new gasket had to seat or be inserted. Then I took the new gasket and put it on place and begining on the top right corner I began to insert the gasket into the channel from the right to the left. Double check to see if was ok
I continued on both sides from top to the bottom, one by one.
When I reached the bottom I began from the left to the right inserting the gasket into the channel. To complete the installation at the bottom I had to pull the gasket a little to properly reach the corner and I finished
To make sure the gasket was on place I hit the gasket with my bare hand all around and I was done.
It was very easy, I just followed the instructions given by the manufacturer

You will need a 1/4" nut driver or socket & extension.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.