CTX18GRNRWH Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Williamsburg, VA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new light socket
Pulled out old socket.pushed in new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gery from Tavares, FL
- Parts Used:
- WR2X7975
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bar end cap broke
Just snapped in.
Was this instruction helpful to you?
Thank you for voting!
broken slide rail replaced both sides
took out two screws both sides useing philips head screw driver put back same way
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Seatac, WA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch wouldn't come out anymore and turn light on
Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from North Chesterfield, VA
- Parts Used:
- WR72X273
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Right side rail of meat drawer cracked
Less than 5 minutes needed to remove cracked rail and replace with new rail. Must have a star wrench to perform task. Very simple task!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert L. from Eldred, PA
- Parts Used:
- WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy fan
Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Sumter, SC
- Parts Used:
- WR24X450
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Fresh Food Door Torn
My experience with PartSelect was excellent. My main concern was ordering the right gasket. First, I found the model number on the inside of the refrigerator. I ran model number on PartSelect and the compatible gasket came up. I removed old gasket carefully pulling it out. I cleaned around the groove that holds the gasket in and where the gasket lays. I boiled water and put it in a cake pan. I warmed up the gasket and smoothed and straighten it out. I started in each corner of the gasket and then worked from each corner pushing it carefully into the holding groove. Took me about 25-30 minutes. It seems to be working great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Wilton, ME
- Parts Used:
- WR24X450
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door gasket had rotted on the bottom
Soaked the new gasket in warm/hot water and snapped it on without any hassels. Thank you also for the fast delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pedro from Miami, FL
- Parts Used:
- WR60X187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge not cooling
Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Tampa, FL
- Parts Used:
- WR2X8504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Office refrig. A rat chewed thru.drain part.
Sears told me the part was no longer available. I came to your web site and then called your customer service. A very nice customer service lady helped me find the part. Very simple to pull the old one off and reinstall the new one with a rat trap behind the unit. Just in case it came back. Could have been a client but probably was a rat. Thanks for the great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Country at from SAYRE, OK
- Parts Used:
- WR55X24065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
A power surge made my side by side refrigerator stop working
I started at the compressor and replaced the overload and the Ptcr first and that did not make the compressor start running again, so I replaced the capasitor and it still did not start, so I bit the bulett and replaced the Main Control Board and that is what I should have checked first, when I removed the old one I found a little burnt spot on the back that I could not see from the front. The new one did not look exactly like the old one, it had two more wire terminals than the old one, but just leave them blank and everything will work just fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Hanover, NH
- Parts Used:
- WR72X273
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken meat drawer side rail
The hardest part was figuring out the part needed from so many little pictures. The actual repair, a piece of cake!
Was this instruction helpful to you?
Thank you for voting!