RS23D011 Hoover Refrigerator - Instructions

replaced electric control board, defrost for six hours. next day (24 hours) same problem, [email protected]

I read what other people had done so I tried the easiest solution--Forced, without breaking, the plastic & fit the ring right where it needed to be.

Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.

Poped ou the old switch, connected new switch and pushed back into socket.

This was easy. Removed the plastic cover at the top hinge. Removed the 3 screws at the top hinge. Lifted the door off of the bottom hinge and laid it on it's side. The part that was worn out is the "natural door closer". It looks like this part will need to be replaced every few years, it is made of plastic and was ground down to nubs. Remove the screws holding it down and replace it with the new one. Lubed it up with some WD40 to get rid of squeaks. I also replaced the lower hinge pin, but I don't think that was necessary.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

First, I removed the water/ice fountain panel - remove the 4 screws and disconnect the panel buttons cable. Second, I removed the panel circuit board - remove the two screws and disconnect the two wire connectors. Third, I pulled the water/ice fountain compartment. Removed the broken rubber pad (actuator pad), and installed the new one -- no tools needed for this step. Finally, I put everything back together. TIP: If the water/ice switch gets stuck, even with the new actuator, find a spring that can fit the switch pin that comes with the actuator. I had that problem, and I simply added a small spring.)

I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!

1. mark location of removable baskets in door and remove baskets
2. remove three screws in top hinge - save shim under hinge
3. lift door from lower hinge
4. remove 3 screws from lower hinge bracket and remove bracket
5. install lower hinge bracket with 3 mounting screws
6. install lower hinge pin in bracket
7. clean upper and lower hinge holes in door
8. lubricate upper and lower hinge pins with grease
9. place door over lower hinge pin - the magnetic seals will hold it in place
10. install upper hinge bracket with 3 screws
11. install baskets in door

Note: The plastic piece on the bottom of the door that mates with the hinge pin and provides a cam action should have been replaced at the same time.

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Most of the time was sent to removing and replacing door shelves. Pry off upper hinge cover. Easy, it's only plastic. Remove 3 fastener from top hinge and remove hinge. Lift door off lower hinge. Lay door down on table let handle hang over edge. Remove door closer attach fastener. Remove and replace door closer. Pry lower hinge up and out. Tap new lower hing pin into place. Replace door, upper hinge and hinge cover. Had to replace Door Closer and Hing Pin together; both were worn and needed replacing.