CTM590 Hoover Refrigerator - Instructions

Removed items and defrosted freezer. I then removed metal shelves, ice maker, bottom sliding tray and false bottom, freezer back, and light bulb with wire track. Cut wires to defrost thermostat and spliced in new thermostat. Reassembled shelves, back, etc., in reverse order. Old thermostat tested "open" in hot and cold water with Ohm meter tester.

Just removed old trim and attached new trim by hand. good results. Happy with your product and tmeliness of delivery Thanks Doug Salter

I love how easy it was to find out what part I needed by seeing the photos to verified it was the part I needed. The repair was super easy and the directions were easy to understand. I didn't even need tools.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

The main issue is that my supports are NOT held on by screws -- they are behind the fridge wall and can not be removed. So this is my solution (ignore the 'fix kit' -- it is useless and is just this part plus a metal screw. It cost me $20 to find this out). Here is what I did: 1) Cut off the old support with a knife. 2) Get a small toggle bolt (I used 1/8" x 2", < $2 from Home Depot) and thread into new support. 3) Dig around in insulation to make sure there is space for toggle to flip open. 4) Install!!!! Wish I'd thought of this before :-)

First I called my friend Robert in Kissimmee, Fl to have an idea regarding the problem because I had never serviced a fridge before. Then he suggested that I check with PartSelect on the Web. Then PartSelect repair videos showed me everything. I followed step-by-step but the problem persisted. I finally realized that the airflow conduit between the freezer and the fridge was clogged with ice. I then proceeded to remove the ice underneath the coil on the aluminum cover and Bingo. The problem was in fact the ice. Well, I only spent $33 dollars for the non-necessary Bimetal Defrost Thermostat. I learned a great deal from that repair.

Removed the freezer door and replaced with the new hinge.

This problem can be caused by 3 different part failures. Timer, thermostat or heater. After contacting a service repair shop I was told that most often it is the thermostat. The cost of the repair would be at least $115. To much for an old refer. So I ordered the part from Partselect for $33. and put it in myself. Step1 cut the power to the refer. Step2 remove ice maker if you have one. Step3 remove base and back panels in the freezer. Step4 the coils were badly frozen so I used a hair dryer to thaw it out. Would have waited a long time for it to thaw out otherwise. Step5 The thermostat is clipped on to copper tubing next to the coils. Unclip it and cut the wires close to the thermostat. Strip the wires and wire nut the new thermostat. Clip it back on to the copper tubing. Put it all back together and start it up. It's over a week know and no problems. Note: We have whirlpool appliances that are over 16 years old. I have repaired the washer, oven, and now the refer with parts from Partselect. Good company. Always received the correct part within about 3 days from ordering. If you are able to do the work yourself you can save big bucks and keep your appliances running longer. Good Luck

Viewed the viedo - it showed what to do

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

took shelf off of freezer, took ice cube maker out, took back panel off changed defrost thermostat.then re-assembled.

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

I just removed icemaker, bottom and back panel cover, remove the old thermostat, cut the wires, connect the new one and replace all covers and ice maker.So far is working perfect, no more water mess inside or on the floor, and my food is not frozen anymore, thanks a lot for your help and your trouble shooting help me to figerout what was wrong, thanks again for save me a lot of money