EF48BDCBSS Hardwick Refrigerator - Instructions

Removed Control plate first. Second, I removed the next section behind the control plate. Inserted the new striker and reassembled.

I pulled the dispenser bin and emptied the existing ice (the maker worked, the dispenser would not dispense). Though there appears to be more, there are about 4 (reciting from memory)very small tap screws holding the front of the dispenser unit to the bin. The dispenser activation screw mounts over protruding items at each end. The item at the back (away from the dispenser gear package) is the drive ring that was broken. The drive ring is a small plastic cup that inserts into an opening at the back of the bin (female side to the rear) and slides into the distal end of the activation screw on the same end. One must line up the small slot on the inside of the drive ring with the end of the screw. Slide the assembly together (make sure that the cube/crush switch rod is properly clipped in place with the return spring hooked to the clip), GENTLY install the 4 or so screws and return he assembly to the freezer. It should work flawlessly. Elapsed time: 15 - 20 minutes.

Easy repair - Don't over complicate it. 1) Flip up ice bar to stop making new ice. 2) Pull out the complete ice bin/tray. 3) shut freezer door while you work on the ice bin. 4) All you need to do is remove the 4 screws holding the ice bin holding tray to the front of the Ice cutting section in the front. 5) Screw drive can then be pulled forward to remove the old/broken white drive cap. Just replace the White Drive ring, put the drive screw back into the ice bin tray and re-install the 4 screws. 6) When re-inserting the bin, you may have to twist the screw drive slightly to re-align with the motor bracket in the back of the freezer. Suggestion: throw out old ice because if it is wet or slightly melted, when you put it back in the freezer the ice will freeze/clump together into a large ice clump; not cubes. Also dry out the ice bin so there is no water to freeze up or create a new jam when the ice bin now re-freezes.

Carefully removed all of the screws to get to the compartment which housed the broken circular door that seals the ice compartment after ice has been delivered via the water fountain on the front of the refrigerator. Disconnected the wire harnesses (labeled as I went) and pulled the unit off of the fridge. It would probably be wise to have shut the power to the fridge off, although I did not. The problem was that the circular door that snaps back into place after delivering ice had severed one of the tabs that holds it in place. I discarded the old door and slipped the new door into place. There is an electromagnetic plunger that is responsible for the door opening when ice is being delivered (the system is magnetized and it draws the plunger in, thereby opening the door) and then snaps back into place once the ice button is released. I found the best way to get this back into place was to put the door (with its harness) into the "open" position and then gently force the plunger into place. Put everything together and all was good.

removed the back cover unplugged the unit removed the old fan blades installed the new easy to pull off and easy to install

Pretty simple really...take out a couple screws and the face plate comes off. Take out the dispenser apparatus behind the face plate and you will see the little lever operated switch that activates the dispensers. Mine had one terminal slightly discolored like it got hot...so that is a good clue. Also, the whole system is pretty simple really, and the switch was clearly the culprit. I got the replacement switch from PartSelect in just a few days, and put it in. The whole deal only takes about 1/2 hour cradle to grave. The dispensers work fine now, and I think I saved at least $150 for a service call. BIG PAPA small

Pulled socket out of housing, unplugged it from source, plugged in new socket and replaced the socket into housing, screwed in bulb and it worked!!

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

Had to replace ice bucket rack because auger motor broke the plastic backing and also the auger motor because shaft was bent on old auger motor. Just followed directions on web site to do repair.

Checked the ice tray and could only find the drive ring had some breaks in the plastic. Actually did not see why this would stop the auger from turning and dispensing ice. However this was the only thing I could find wrong with the unit. I pulled the tray, removed 6 screws (star tip heads) pulled the auger forward and replaced the drive wheel, put the unit back together and its been working fine ever since.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect