EF42BDCBSS Hardwick Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janet from PITTSFORD, NY
- Parts Used:
- WPA3073101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
No problem
I had a son put in the new light bulbs. Rather simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conrad from MEDINA, MN
- Parts Used:
- 67001454
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Lower bushing in hinge fractured, resulting in squeaking door
Remove upper hinge with socket set. I found it helpful to remove the door spring (on bottom of door) in order to be able to lift out the door from lower hinge. Replace bushing. Replace door, upper hinge, you're done. I did note that lower hinge post (~10mm OD) had worn against the frame due to the loss of bushing, losing ~1-2mm of metal. Would not have seen this until the door was off. Was concerned this will lead to premature failure of the new bushing, but it will be a much harder job to replace lower hinge (looks like I will need to empty and tip the fridge to access lower side), plus I didn't have the lower hinge part handy (~$40-45), so I will replace both if the bushing fails again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WALWORTH, NY
- Parts Used:
- WP61003336
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The ring was cracked and it would not dispence ice.
I switched the ring and still had the same problem. What caused the Drive ring to crack was the Ice maker drive was cracked also, when it filled with water it would tip. The ice was not freezing completely and would cause the ice to build up and the auger was froze with ice or a big piece of ice would jam it. So I replaced the Ice Tray, it is working like new. I have to buy another ice tray as inventory, although I know inventory is bad but I never agreed with that theory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PHOENIX, AZ
- Parts Used:
- W11613295
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The refrigerator was working for just 1 minute and breaks, I discovered that the fan was not working , I understood that there wsa something wrong with the condenser fan motor. I just order a new one.
The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mon from NORCO, CA
- Parts Used:
- W10841139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
not pumping at all
running like a brand new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from BEN WHEELER, TX
- Parts Used:
- 12001773
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Ice Maker would not dispense ice
Had to cut the old part off with dremel then just install new part and put back in refrigerator. It is a good thing to know that the Yoke is a left threaded. Thanks James from Pineville.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boyd from North Fork, CA
- Parts Used:
- WP61003336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice bin drive ring broke
Removed the screws that held the main ice bin and slid back the bin to leave space behind the auger to remove the broken ring. Replaced with new ring and replaced screws to hold ice bin back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from SMITHFIELD, RI
- Parts Used:
- W11613295
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The referigerator is warm, but the freezer is cold.
I noticed the coils very dusty dirty, tried brushing it clean, ended up blowing it clean. I noticed the condenser fan motor was never turning, I had power, so I ordered a new one. I actual received the evaporator motor, so I had to order the correct one. After changing it, and it started blowing right away. But my refrigerator is still warm. I do not know where the evaporator blower motor is located. I cannot make out from the diagram breakdown. HELP
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerlene from BERLIN, MD
- Parts Used:
- 61004388
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Soring old, need replaced. Air leaking in and melting ice
Followed included instructions. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from WESTFIELD, IN
- Parts Used:
- WP628356
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
broken hinge bearing on ice maker
Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary L. from Millsboro,, DE
- Parts Used:
- WP627843
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from Escondido, CA
- Parts Used:
- WP61003336
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken ice bin drive ring
Removed 6 screws to get at broken part. Had to remember the disassembly sequence to properly reassemble. The whole process was relatively simple. I saved about $125 which would have been the cost of a repairman coming to the house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Discovery Bay, CA
- Parts Used:
- WP2182124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The ice stripper cracked from freezing.
There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from Parrottsville, TN
- Parts Used:
- WP61003336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Metal Augar Damaged End On Plastic Ring I
Removed drive assembly end of ice bin using socket wrench to get to old ice bin drive ring. Pull drive sssembly back to get ice bin ring out of the other end of ice bin. Installed new ice bin ring and and reinstall drive assembly end.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from ponchatoula, LA
- Parts Used:
- WP61003336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no ice in bucket
looked a website removed part found broken item order and installed in 15 minutes, easy simple fix very low cost change
rl
rl
Was this instruction helpful to you?
Thank you for voting!