GRT17CRAW0 Gibson Refrigerator - Instructions

The old drain pan had a 1 ½” tall bushing attached to the center of the pan. The new pan did not have this bushing which was great. I had to cut about 1 inch off the bushing to remove the old pan. Also after cutting the bushing I had to screw the bushing off after cutting the old pan from the bushing. I installed new pan onto the ½” of threads that was left on the top of the compressor. Checked repair two days later all was great.

Ordered new parts, removed old parts, put in new parts. Done.

The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.

I followed the advice posted by others at parts select website. This made the repair process easier. Everything went very well, and my refrigerator is working just fine. I definitely will use parts select in the future for any appliance parts and repairs I may need.

Replace evap fan motor. Take a close-up picture of the evaporator fan motor installation prior to removing. Take pictures as removing various components.

It was fairly easy to replace the thermostat. Unplug the refrigerator first. Then remove the refrigertor light bulb and 3 screws on the plastic cover that houses the thermostat and defrost timer. Unplug the thermostat from the wiring on the refrigerator and remove the plastic housing holding the thermostat. Remove two screws holding the thermostat and replace with the new one. Put everything back together in reverse order. Unfortunately, this did not corrrect my problem. The refrigerator is well over 30 years old and I had narrowed down the problem to the thermostat because the old one was hard to turn to adjust. About 10 years ago, I replaced the defrost heater in the rear of the freezer compartment for the same problem, and didn't think that would be the problem this time. Well, as it turned out, I checked the resistance on the defrost heater and it was was bad again. I replaced the heater this week I got from PartSelect, and the refrigerator cycles fine now. Replacing the heater is a little more work that changing the thermostat. You have to remove the freezer compartment fan, fan vent, and back inside wall of the freezer section to expose the coils and the heater element. You just need a socket screw driver. Then you have to reach inside and unplug each end of the heater to check it with your ohm meter. A bad element will show up as an open circuit. Then to replace it, you have to maneuver it around to get if away from the coils and remove a couple of clips. Anyone with some common sense can do it, but it can be a bit challenging.

Removed the old burned out evaporator fan, and with the model# was able to find a replacement at PartSelect. I was really surprised that you had the exact part on a fridge that old. Installed the new fan, and the fridge is working beautifully. Thanks to PartSelect I was able to save several hundred dollars.

This is a top and bottom frige. I unplugged the fridge and I took off the sheld in the freezer and removed the blower fan cover and unplugged the fan to remove the back freezer panel. Be careful when moving the fan. It looks sensitive. I used a hair dryer to melt the frost to get to the screws. Because it was frosted the back panel was hard to take off. Don't force it too much, just keep melting the ice. Once it was off the radiator looking thing was completely frosted and iced over and I couldnt even see the thermostat. I started blowing it with the hair dryer and it started melting. It took an hour to get the ice melted enough to actually see and remove the thermostat. You may want to leave the fridge off for a day. I didnt have a choice because I didnt have anywhere else to place the food. I was using the freezer as the fridge. Thats how cool the freezer was. I cut the wires for the thermostat. Im sure you could check which is positive and which is negative. I just looked at the direction the wires went. This works but it is not guaranteed. Check for ground. Google it if you need to know how. I used the clamp connector things but I didnt have a clamper so I used a plier. It works but I didnt like how it clamped. The little tubing didnt work for me becuase I didnt have a solder gun to warm it up and using a match is not good. You'll burn the wire. Buy electric tape and wrap it around. Dont use regular tape. Go to home depot it costs 99 cents. Make sure all ice is melted. Go over everything with the hairdryer to melt the ice. You dont want it to start freezing and clog up the vents, expsecially the one that goes from the fan to the fridge. Before I put everything back together I changed the defrost timer because I figured its best to change it since you never know. I loosened the two screws but first I took offf the screw holding the timer panel. I changed the defrost timer and connected it back. Then I screwed everything together. Then I screwed in the back freezer panel but not the fan cover so I could see if the fan is working. I plugged in the fridge and the fan didnt work. If you look under the defrost timer panel, the timer has a round part that you can move with a flathead screwdriver. Move it lightly clockwise and the fan will start. I read that the fan goes for 8 hours and then it turns off for a half hour. Seems like a lot of time to be on but its been a week and the fridge and freezer are working real good. This website is good and the aprts are cheaper than Sears.

I went on partselect put in make and model number, a list showed the probable cause. I watched the how to video. When I received the part in short order I loosened 2 screws disconnected the wiring plug (sprayed it with contact cleaner) pluged it in, removed screws from old part put them in new one. Put timer back in its location and tightened the screws. Very eazy, works fine.

I pick up very fast at these kind of small jobs but because of my very busy schedule I decided to call (2 times) technicians about my problem but none of them had any idea. About my repair, I removed the grill at the bottom of the refrigerator, unscrew a small plate (located on the bottom left side) that's holding the defrost timer. I plug on the new part, screw back the plate with the defrost timer and that was it. Don't forget to turn clockwise with your finger the timer until you hear a "click" and then turn it slightly more to the right. There is also a video on U-tube.

open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.

real easy with the help of the video , made the difference

Took off the old crisper drawer cover supports with the screw driver and put the new ones with the screw driver and small hammer (really easy)thank you to your installation instructions video.

pulled out freezer, went to floor,reached in next to compressor pulled off clip just like on the video.Pulled off old capacitator took off wire leads.Installed new one. Freezer runs great.Loaded it up with beef pork and venison. No problems.