GRS22PRAW0 Gibson Refrigerator - Instructions

I didn't know the front of the drawer could come off so it was pretty gunked up with dried meat juices that had leaked. The fit was very tight. I had to really work the putty knife to get it between the front and the drawer at the bottom where the catch is. I was afraid I would break or chip the front before I got it off but it handled the pressure pretty well. Had to use some force though. Once I cleaned the front it slid right down and snapped into place.

I took my time to remove the front off of the old drawer,by gently prying it apart with two screwdrivers, this was the hardest part, the front installed very easily . The shippiong time was 2 days instead of three. Will use partselect again.

First we took the the old drawer out and pride off the front clear covering on both sides. Then we placed the front covering on the new drawer and fit it in place. This had to be done twice since it did not take the first time. It had come loose after a couple of days and we snaped it back into place. It has done fine since.

My husband just dislodged the front of the old drawer and very carefully slipped it into the new drawer. Presto all fixed. Very easy. So happy with the new drawer that is so easy to slide open. We had taped the old one for quite a few years. Wish I would have thought of looking up this web-site earlier! Thank you so much for this new drawer!!

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall

took door off. sanded rusting hinge and greased. installed door hinge washer. I had to install a larger washer over hinge bearing to help support the door where it was rusting. no sweat. works like its new. thanks to you guys for having the parts.

just like the video showed...it was excellent!!!

The job was as simple as could be pry away the old and push in the new.
Only wish I had done years ago. Tthis is a great service to customers.

Ordered the parts from the product discription (photo) as well as chart showing actual size. Got the parts( in two separate shipments) cut the bar to length and snapped them inot place. Bingo!

took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

I order defrost timer then replaced it but it seemed doesn't work. I order defrost thermostat again then it worked fine until now. Thanks. Part selects.

Unplug the refrigerator. Removed the right hand top shelf. Used a 1/4" nutdriver to remove rear center mounting screw for Control Housing. Used Phillips screwdriver to remove two mounting screws for timer. Unplug cable from timer and plug it into the new timer. Install the new timer and re-install the Control Housing. Plug in the refrigerator and adjust the timer to start the unit. This was a snap with the diagnostic provided by Part Select. At first I thought it was the fan rubbing but when I removed the cover (two screws) it was obvious that wasn't the problem. The diagnostic hinted that it was either the timer or the motor capacitor making the noise. Because the noise continued after turning OFF the control, I thought it was the timer...I was right.

I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.

I watched the video online where it described the troubleshooting tips for this type of symptom. So I knew exactly what the problem was which is the defrost timer. After the part came in I just unscrewed (4 screws) the box which houses the thermostat and the defrost timer from top ceiling of the refrigerator section. Then I just unscrewed and unhooked the old defrost timer and replaced it with the new one. After finishing the installation I turned the fridge on. At first nothing happened. So I turned the dial on the defrost timer with a flathead screw until it clicked and the fridge came alive. I waited for an hour or so. The cooling cycle completed and the fridge stopped as expected. When I opened the door I noticed the interior is much colder than before and right after closing the door the fridge hummed back into life again. So I know my fridge is working again. Thanks to PartSelect for providing the right part for my refrigerator. I will definitely buy from them again if anything goes wrong.