GRT18QNCW5 Gibson Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Spokane, WA
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Temperature in both freezer and fridge sections to warm!
Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Sunnyvale, CA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No freezing or cold in either freezer or refridgerator - compressor did not run.
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sadrudin from SAN DIEGO, CA
- Parts Used:
- 218396700
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
The hole on the handle mounting block was too low
I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Pima, AZ
- Parts Used:
- 5303917954
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator keeps frosting up and not cooling
Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, going to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Newton, KS
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Sierra Madre, CA
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Coils kept icing and refrigerator stopped cooling lower compartment.
Replaced defrost timer & thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEFANIE from Killeen, TX
- Parts Used:
- 218971302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My drawer rail broke off on the right side.
The process of repairing the draw was very simply. First I removed the broken part with a screw driver and simply slide the new part on and secured the part w/ a screw and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Eatonville, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defroster didn't work
Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE
Cool.
GWE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Batavia, IL
- Parts Used:
- 218971302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Meat drawer kept falling
I removed the screws from the old rail, which was broken, and installed the new rail using the old screws. It was very easy, and I wish I had fixed it months ago when it first broke.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DEBORAH from BALTIMORE, MD
- Parts Used:
- 218971302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My grandson pulled the drawer down,and broke the rail.
The repair took less then 15 minutes,my husband put the new rail on,he used a screwdriver,now I have a folder just for partselect/fridge.My
grandson is 4years old,and he can do some stuff.
Thank You
It came within 5 days.
grandson is 4years old,and he can do some stuff.
Thank You
It came within 5 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus from Pine Hill, AL
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
frezzer iceing over and not cooling the refrigerator
Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Clevelamd, TN
- Parts Used:
- 215473602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
End caps broken
End caps snapped out of door,
Replaced with new caps
Replaced with new caps
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Coralville, IA
- Parts Used:
- 215473602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door end caps were broken and not fixable
I simply placed the retention bar between the new end caps and popped it into place. Took about 10 seconds to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Orange Park, FL
- Parts Used:
- 215473602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clips on both end caps we broken and the crossbar kept falling off.
First i pulled the crossbar off the door, then I pulled both end caps off the crossbar and then I
put the two new end cap on the crossbar and then tapped snoggly into place with the palm of my hand. Job done. took all of about 5 seconds.
put the two new end cap on the crossbar and then tapped snoggly into place with the palm of my hand. Job done. took all of about 5 seconds.
Was this instruction helpful to you?
Thank you for voting!