GRT17G4AW0 Gibson Refrigerator - Instructions

First, I removed the screw holding the support rail and, because of using super glue to attempt a temporary fix, I had a little difficulty in removing it from it's location.

Since I have "tremors" next time email me a repairman.

Thank you.

Robert L. Enox

I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.

I removed the plastic shroud on the ceiling of the refigerator, unscrewed and unplugged the old defrost timer, and replaced it with the new one. I reinstalled the shroud with the new timer installed.

I just took off the broken piece and replaced it with the brand new piece I got from Partselect.com. The part was like three bucks and shipping was a little over 5. I fixed the bottom shelf for under ten bucks. I didn't think I'd be able to find the part on the net, but a quick google search led me here. My wife was always nagging me to fix it. The duct tape I used just wasn't good enough for her. Now, with partselect.com I made her dream come true! David Bueno-Hill

The knob came in the plastic package. It was the correct part. I opened the package and placed the knob on the prongs. Now it works fine.

Thanks
John S.

Put the pieces that came together, and crimped the retainers with padded pliers. Installed in to the door snap clip retainers 3 minutes start to finish.
The REALLY impressive part was that I did the standard FedEx shipping which was supposed to be 5-7 days. I received the parts 28 HOURS after I placed the order. This was way above and beyond the term "good" Customer Service. The service was OUTSTANDING. So much so that I got to place a call I seldom get to make back to PartSelect to thank them for the outstanding service. I give them 5 stars and will use them again as well as referring my neighbors and friends to this business.

I attempted unsuccessfully to glue this piece several times. Then my wife got the idea for me to search for a replacement on line. It took me less than 5 minutes to reassemble the door rack and reinstall in in our refrigerator. no tools were required. The part fit like the factory original. I wish all repair jobs were this straight forward and simple to do. Having the correct part makes it more than easy. We were both more than pleased with the price and the delivery time.

Thanks Part Select!

Unscrewed old rail. Screwed on new one. Replaced drawer. Voila!

Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.

inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!

Took out top shelf, remove old screw and rail . Replace with new

After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you

Thawed out freezer, I recommend laying a couple old towels in freezer to soak up melted ice. Replaced old thermostat with new part. Removed 2 screws, removed back plate, unplugged 2 connectors and cut 2 wires. Crimped in new thermostat and repositioned to original part location. Reconnected plugs as I reinstalled back plate. Installed 2 screws and connected power. Works like new! Trouble shooting and part installation video is very helpful, great site!

This is super easy. You just pop the old supports off vertically, pull the bar off of the broken one(s), replace them with the new one(s), then pop the whole thing back onto the door of the fridge by pushing down on both sides.

My upper and bottom air diffuser was missing.
Purchased both air diffuser and placed it.