GRT21PRCW4 Gibson Refrigerator - Instructions

Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.

Heard the snap of a short circuit followed by a burning smell around the refrigerator. Pulled it out, unplugged it and removed the back panel with a nut driver. Plugged it back in and when the compressor kicked on I saw sparks and some smoke at the relay. Unplugged and ordered new relay and the associated run capacitor in case it was also bad.
Removed the holding clip and the relay with capacitor easily came out with two wires attached. Removing the wires was done by prying with needle nose pliers with some difficulty.
Inserting the wires into the new relay was also difficult. If the position isn't just right it does not snap in. Once it is positioned correctly it makes a positive connection with not much effort.
Reassembled the capacitor, plugged unit into compressor, added retaining clip and plugged in refrigerator.
Compressor started up correctly. Note that as the refrigerator cools the compressor will shut off for long periods of time. This is normal.

Took old defrost pan off, put new one on. Had to bend new defrost pan a little for it to fit..

attached the bar to the end piece and slipped it into the proper opening. Easy I ordered the piece one morning and received it the next morning. Great service.

First, my husband removed the shelf assembly. Then he unscrewed the boken bracket. He then screwed in the new bracket and proceeded to install thecomplete shelf assembly back into the fridge. Placed the meat drawer back into correct location, to fit back into rail brackets. All done.

Simply popped the new end caps into place with the old guard and now it is tight and secure. Easy Peasy. Of course all this is after the operator at PartSelect ordered the right part for me; I had ordered the freezer door end cap, not what I wanted. I received the correct part the very next morning. Returning the wrong part was a breeze too.

Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!

From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

removed freezer door and installed the new one. This was a pretty easy thing to do, although putting the old handle on the new door was a challenge. No knowing that there is a plastic piece holding the top of the handle i broke the that piece and had to order another one. Mean while the freezer was making alot of frost inside, so that had to be cleaned after the new part came.

All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.

Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.

Placed end cap on one end of rack and attached to one side of the door by applying hand pressure.
Inserted the other end of the rack into the end cap'
and again applied hand pressure to insert into slot, Repairs completed.

First I removed 2 screws and removed broken railing then placed new railing ad screwed in new screws then replaced drawer into railings. Thank you so much for the excellent service in geting me the correct part in a timely manner.

I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.

I unsnapped the old clips from the bar, installed one end cap to freezer door, clipped other end cap to bar, slid bar into end cap installed in door then snapped other end cap into place. Repeated for second shelf bar as those end caps were broken as well. No tools were needed.