GRT17G4BQ3 Gibson Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- john from NEWHALL, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Evap fan motor comes on and off will not stay running
pulled back panel to get at evap fan motor cut wires to remove reinstalled hooked up wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from ODESSA, TX
- Parts Used:
- 5303918549, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Fridge was't cool
I just followed the instructions on the videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mikaeline from SYCAMORE, IL
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken rail replacement
Removed shelf from frig. Removed screw of broken rail. Replaced with new rail with screw. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from TALLAHASSEE, FL
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawaer support on right side of top shelf broke
Unscrewed screw from back of shelf pulled broken part out of slot it holds in and replaced with new one screwed the piece back in place.
Was this instruction helpful to you?
Thank you for voting!
Door racks broken
Refrigerator door racks broken.
Removed old ones and replaced with new door racks. Just snap on.
Removed old ones and replaced with new door racks. Just snap on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from COTTONWOOD, CA
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Draw support rail broke.
Removed top shelf. Removed rail screw and old rail. Install new rail and use rail screw to secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from MARKLEYSBURG, PA
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The slide rail(Drawer Support Rail) I found was made very cheaply. None the less I had to replace it. I did watch the Repair tutorial on your site that made the repair a snap. Ezpeeze!
Removed the shelf and one screw on the back of the rail. Replaced rail and screw. Re-inserted the drawer and it was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from NEW YORK, NY
- Parts Used:
- 240535101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door rack broke
Ordered new one. Popped it in. Very Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PHILADELPHIA, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Evaporator was freezing up and was running non stop
I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Pottsville, PA
- Parts Used:
- 240337712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Dairy door was cracked by an item in the refrigerator and broke into two pieces
This was not technical at all. The old door fell out and the replacement door snapped right into position. It was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from CAPE CORAL, FL
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
FREEZER COMPARTMENT NOT COLD ENOUGH (20 DEGREES)
REPLACED TIMER-DEFROST 215846602..REPLACED THERMOSTAT-DEFROST KIT 5303918202..REPLACED CONTROL, TEMPERATURE 5304421256..RECHARGED SYSTEM WITH 134A...ALL FANS WORKING...COMPRESSOR RUNS.. FREEZER STILL NOT GETTING COLD ENOUGH...HOLDING AT 20 DEGREES...ANY SUGGESTIONS..THANKS..DAN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karla from UNION, MO
- Parts Used:
- 241554901
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Refrigerator light stopped working
The bulb wasn't the issue so I was hopeful the switch was. utube helped me some, but figuring my model was different than any on utube. Got the switch in and plugged it back in. Moment of truth. Didn't light. Ugggh! Out $50 for switch plus $20 for nut driver set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sadrudin from SAN DIEGO, CA
- Parts Used:
- 218396700
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
The hole on the handle mounting block was too low
I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Newton, KS
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Taylor from Greenville, SC
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic support on rail had broken off
Easy peasy... took the shelf out of the fridge. Unscrewed the old rail. Screwed in the new one. Put the shelf back in. DONE!!!!
My local appliance repair shop said they would have to order the whole shelf in order to fix my problem. It was going to cost $50 and I'd have to wait 3 weeks.
Instead, I found you guys on the internet. The part cost $5 and I got in delivered in 2 days.... CAN'T BEAT THAT!!!!
Thanks
My local appliance repair shop said they would have to order the whole shelf in order to fix my problem. It was going to cost $50 and I'd have to wait 3 weeks.
Instead, I found you guys on the internet. The part cost $5 and I got in delivered in 2 days.... CAN'T BEAT THAT!!!!
Thanks
Was this instruction helpful to you?
Thank you for voting!