GRT21PRCD4 Gibson Refrigerator - Instructions

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

Popped off the front plastic cover on the bottom of the fridge, under the doors. Two screws held the defrost timer on under the front side of fridge (below freezer door). You can't really see the timer except for the adjustment knob that is accessible through a hole. Once the screws are removed, disconnect the wire plug and remove and replaced unit. Works fine ever since.

took cover off inside freezer control . removed old fan and unpluged wire harness plugged new one up and fastened back in place and put control cover back on.

Tapping on the thermostat control would start the compressor, but after cycle was complete it would not start again on it's own. Seemed like a slam-dunk that the control contacts were worn out. PS had the right part in stock, and it arrived quickly. Nearly identical to the original part, it installed without any problems. One minor glitch, though - the mounting tabs are tapped for #6 screws, but the original screws were #4. Since no hardware was included, I had to dig up larger screws to make it work. Not a big deal at all - but it would be handy to include these screws. Works just like the original, maintains inside temp just fine. A no-brainer for 65 bucks. This fridge is 15+ years old, and now serves as a beer cave. Cold beers for everyone!

The BIG problem was getting the old drip pan off. The bolt on top of the compressor was too long to allow the removal of the old drip pan. I removed the old drip pan by cutting most of it away with tin shears then cutting the remaining part of the pan around the bolt with a hack saw (taking care not to damage freon lines and raising the pan above the threads of the bolt so as not to damage the threads). I still had to cut half the bolt away with a hack saw by replacing the nut and cutting a third of the bolt away (above the nut), so the new pan would fit. Putting the new pan on was a breeze after that. It may be easier to just cut the bolt off altogether on top of the compressor and use the wire clips per the instructions supplied with the kit to install the new one.

just took the back cover of the freezer of and then the fan. To do this, I just removed like four bolts at the corners and then four bolts that attached the fan to the cover. At the end, I just unplugged the cables. I got my new fan the very next day, which was like extremly fast, plug in the cables and attached the fan to the cover and then attached the cover to the original place. It's a pretty simple repair. My fridge is now working like it should be.

The end caps worked perfectly for both the Frigidaire and Westinghouse fridges. Just pulled out the old end caps and then literally just pushed in the new ones (remember to attach the shelf bar before attaching the second end cap!). The pieces arrived quicker than expected. Thanks Partselect!

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Simple switch repair: Unplug fridge, pull down to remove switch assembly, slip contacts off. Reverse with replacement switch. HOWEVER, check first to see if the bulb filament might be broken, as this could cause the same symptom. OR in my case, the light socket connection was the culprit. Check that too before ordering a replacement switch.

1. turn off the refrigerator using the inside temp dial
2. take all food out of the refrigerator door
3. pull up the gasket along the door frame and loosen all
the screws starting with the bottom and the sides
4. loosen the screws underneath the gasket on the top of
the door (be ready to lower the door frame when you
loosen the last screw!)
5. pull the old gasket off the door frame
6. put the door frame on the floor insulation side up
7. lay the new gasket out on the floor and use a blow
dryer to heat the new gasket to make it flexible
8. put the new gasket on the frame by fitting the crease
of the gasket over the edge of the frame making sure
that the magnet side of the new gasket is facing the
refrigerator when the frame is re-attached
9. apply RTV Silicone sealant along the entire lip of the
gasket (on the insulation side of the frame) and press
the gasket to the frame to form a bond ( I got a tube
of RTV silicone at Wal-Mart in the automotive dept. near
the motor oils)
10. wait 5-10 minutes to let the silicone bond to the frame
11. lift the frame up and re-attach to the door starting
with the top middle screw first, the side middle screws
next, the bottom middle screw last (you may want to get
a second person to help hold the frame while you are
attaching these initial screws)
12. go back and re-attach all remaining screws
13. close the refrigerator door and check for a good seal
all along the gasket
14. your done!

Note: you may want to close the refrigerator door and block
it with a chair to keep in some cold air after you
remove the frame to install the new gasket

I pulled out the old pieces and poped what I couldn't into the foam insulation behind the support. Then I placed the new piece in the hole and popped the plastic pin to seat the support. bang. the only problem I had was knowing if it was the right part by the picture. The little pin that had to be pushed through kinda threw me.

removed doors and took out screws from hinge and replaced hinge. works great, all costs under $20, applinance store said no parts available only wanted to sell a new appliance, no wonder they are all losing bussiness when they have custmor service like this!

Twisted replacement bulb into place easily. Let there be light!

I removed the plastic cowl in the rear of the freezer to gain access to the fan, took out two screws that secured the brackets holding the fan. Then I separated the coupling wires which had a sort of locking mechanism that was simple to undue. I took out the brackets along with the fan, separated the brackets and removed the screw for the ground wire. Then I simply reversed the process.

Did the obvious. Removed the stick-out cover, then the back of the freezer wall, after taking the bad evaporator fan out. Replaced the old motor with the new one, stuck the fan blades back on, and put the replacement back in place. Checked to see that the new motor and fan, before final hook up, had no issues. That was a success. However, when I put the parts in place, I had some significant vibrations. By taking things apart and re-doing the install, the vibrations went away. However, the final install, even if quiet, did not work. Apparently the condenser was kaput. No cooling after all the adjustments. We gave up and are replacing the fridge.