GRS20HRHD0 Gibson Refrigerator - Instructions

I ordered the part, easily installed a new one. Everything works greatnow.

Removed the timer, installed the new one. Great service from part select

first I replaced the timer control hoping thats the problem,unfortunately situation the same ice build up on the freezer.so I replaced the defrost thermostat.right now I'll still observing the condition if still the same.may be in couple days.so far its good.and to replace the parts is not difficult and easy.

Ordered parts and three days later the parts were at my door. Took longer to clean stuff out than to replace the drawer supports.

bottom left cornerof fridge defrost timer replaced two bolts and a wire

we removed the food from the freezer, disconnected the fridge , removed the cover, the evaporater fan was running, condeser fan was running, then we checked heater with multimeter and it was ok. next step we replaced the frostimer, and defrost thermostat . and then the refrigarater was working ok, problm was the frost thermastat damaged.

I watched the video you had on-line and it was simple. Thank you so much

After reading other posts, I decided to change the defrost thermostat, so I watched the videos, and did that. It got better, but the problem persisted, and the ice was still building up in the freezer section. So I decided that the problem was with the defrost heater. I ordered a new one, that was here under 24hs (using the Fedex ground). I replaced it, measured the old one and saw that it was not passing any current at all (so it was really burnt). Now the fridge is good as new, maintaining the proper temperatures both at Freezer and Fridge sections. Thank you Parts Select ! With $ 70 in parts I was able to get back my appliance working !!!

there were three possible problems the timer, the thermostat, or the heating element.i replaced the timer first as that is the problem 65% of the time and that did not fix the problem, i replaced the thermostat and that did fix the problem. after watching the video on line from parts select i took the back off of the freezer from the inside, defrosted the coils with a hair blower and then swapped out the thermostat which pops right off and i spliced the old connectors to the new thermostat. the heat shrink tubing that came with the part was a little to big so i put a smaller peice on each side for water proofing. that is what the cigarette lighter is for to supply heat to the heat shrink tubing.now that i have fixed that problem i may tackle the ice maker next

Ordered the new part-Unplugged the refrigerator - took off the cover over the defective timer - put in the new part put the cover back on - plugged the refrigerator back in - so far, so good!~

I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises

1 went with maj 69% said defrost timer. NO. 2 went with second choice run cap NO. 3 went with my thought, ( PTC Starter ) why not, most exp part. Fixed the problem.

Purchased switch and socket, not sure which had failed. Moved all frozen food to refrigerator, turned off breaker. Used nutdriver to remove two screws holding box containing switch and socket. Removed old switch and socket. Removal was slightly difficult since cabling came off both sides of the box. Installed new switch and socket and bulb. Turned breaker back on, checked light as workiing. Replaced scrrews to re-intstall switch box ( or whatever you call it ) Closed door and waited for freezer to cool. Returned all frozen food to freezer. Job Done

it was great. I ordered the capacitor for my frigidaire frig and it arrived
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks

Very simple...I followed the instructions given from someone on this site! I received the drawer within 2 days from purchase. I went on this site for tips to replace the plastic removable front piece. I just used a kitchen knife and gently pried the front away from the drawer and slid the front up and off. Then I slid the plastic front onto the new drawer. Very easy and quick.