GSS22JETC General Electric Refrigerator - Instructions

I shut off the water at the shut off valve when I discovered the leak. I started checking on the web for a part and I found PartSelect.com and I couldnt believe there price!! I had checked with a local dealer and it was several dollars cheaper here.Back to the repair i remove the vent cover on the back of the unit about 8 screws and then there was on screw holding the water valve and three water lines to lines use the puch in method and one is screwed on , i simply remove those and reinstalled the new valve with the coresponding lines. in a few minutes i had ice and water out the door good as new!! I also took the time to install a new five yr water filter!! actually this water valve is much quieter than the origianl I am well pleased with PartSelect I will do bussiness with them again!! Thanks Bob

I followed the directions provided by Robert of Florida. My contribution is, be aware that the plastic nut on the auger shaft turns to the right to loosen.

Removed panel from inside the back of the freezer section, by removing four screws. Then, sprayed the ice build-up on the coils, with hot water until all of the ice was melted away. (Note: be certain to plug the drain hole, and use several towels to catch the water drainage. ) Removed the Defrost Heater Element by removing two holding screws. Unplug the unit and pluged-in the new unit and replaced all screws as originally mounted.

By reading another customers tip I decided that my problem was the exact same. I had to order the entire motor not just the auger because the motor shaft was stripped. Once you remove the motor, hold the shaft with a pair of vise grips and use a screw driver to turn the auger off clockwise. The threads are reversed. The new auger screws easily onto the new motor counterclockwise and installing back into the fridge was a snap.

After removing three screws on the ice bucket, it basicly came apart by itself. I needed to use pliers to remove the old nut because it had over tightened itself onto the shaft. Be careful here - it is a left hand nut - not a normal right hand nut! Reassembly was a snap putting the parts back together in reverse order. Unit has been working great since the repair.

removed 3 screws with 1/4 " nut driver, unplugged 2 plugs by prying out on side tabs, removed bracket and motor. Used vice grips to hold motor shaft and used screwdriver to turn auger fork clockwise and remove. Unplugged two connectors from motor. removed 3 screws with 1/4" nut driver to remove motor. changed rubber boot from old motor to new. Reversed procedures to install new motor on bracket, auger fork, bracket in freezer, etc. Only difficulty getting both hands in narrow freezer compartment. Still didn't work, called repairman. When he got here I showed him the problem and lo and behold, now it would not dispense water. He diagnosed it as a bad motherboard, replaced it and all good now. Motherboard $150, diagnose and labor $90, but it is all good now and I even have a spare motor. The failing mother board causes strange howling noises at times and we discovered the compressor fan had also stopped working and in a short while I would have had a bad problem. Caught it just in time!!!

I followed the isntructions of another fellow who had repaired his ice maker, but made the mistake of taking the ice crushers apart before noting where the fixed blades were to be reassembled. Since there was not a schematic with the part I had to go on line to your site and enlarge and use the one there, while accurate, was very hard to read and when I finished, I think it is in the wrong place as I'm not able to get the fineness of crushed ice I had before the repair, but absent a very legible schematic I'm not going to try to fix it further. The auger works, gives us ice cubes and half crushed cubes.
Another tip for future repairers is to to wait for the ice container to warm up or use a hair drier on the part where the tabs need to be depressed to slip off the blade housing. When cold it's extremely brittle, but since I had to leave the job for later at one point and left in on my work bench I found it much more pliable and easy to assemble.
All in all, I'm OK with the part and the result, but wish I could have gotten the fixed blade back into the right spot.

I had lost the bottom hinge during a move and so I rigged the hinge using an old tv antenna and the door never really quite worked right and it was VERY annoying. I stumbled upon this site and was surprised how inexpensive the part I needed was. I was very impressed with the speed of shipping and the install took maybe 5 minutes. The fridge works as good as new. Thanks a ton!

Total time to replace both slides was ten minutes. It took me longer to take the stuff off the shielf than it was to fix the slides!

I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing

They don't make appliances like they used to. When my little butter door cracked, we kept using it until it finally fell off for good. So, where do you buy one of these? When I turned to the internet, I found a few places but they were toooo expensive. PartSelect had the right part at the right price. I figured that if I bought another little damaged part, the light cover, at the same time, the shipping cost was essentially halved, an even better deal. I was so surprised when my parts arrived faster than I expected, a couple of days by regular mail. That's faster than I could ever get a service call and who's going to call a repairman for a simple thing like that, anyway. If not for PartSelect my reputation as the Queen of Duct Tape would still be intact. I didn't want duct tape holding together my newish SS fridge in my redone kitchen. Imagine tile, granite, stainless and duct tapeI placed the little door in the fridge and now the butter stays put. the lower light shield is just as easy.

1) Unplug Refrigerator. Remove all shelves and light shield in the freezer.
2)Remove panel covering refrigeration coils inside freezer in back. Two hex head screws w/nut driver.
3)Remove the defrost heater using phillips screw driver. Two screws.
4)Unplug two quick disconnect stakons and wires from heater.
5)Plug the wire coming down the right side into one side of the new heater and plug the shipped white wire into the other quick disconnect spade at the heater.
6)Install the new dual element defrost heater into the same place where the old was. Connections to the right.
7)Route the wire that was on the left across the top of the coils and down the right side.
8)Bring the existing wire from the left side down the right side and the white wire up the right side. Wires should not be tight at all and do not remove the tape at the stakon.
9)Now wires need to be cut (if necessary)and crimped together in the shipped stakon. This stakon looks like a wire nut.
10)Wires should be tucked gently into the styrofoam up and down the right side. Wirenut should be positioned so that water can not collect in it.
11)Replace the panel over the cooling coils.
12)Plug Refigerator back into the wall outlet. Put shelves and light shield back in.
13)My refrigerator is now working without a problem. It's been est two weeks.
Ice maker is also working correctly.

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

Removed the ice bucket and put the new ice bucket in placed
.
work like a top.

I am 80 years old, female. Repair was a challenge but I was determined as my son said Mom you can do it. The video was wonderful. and I did a lot of rewinding etc. Hardest part was taking apart.. screws tough. All in all not bad. I don't want to do it for a living though!!!!! Ice is now dispensing!!!!!!!!!!!!!!!