90488JF General Electric Refrigerator - Instructions

The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.

Found your web site and bought a couple of replacement parts from you guys and reaaembled unit. Its now working. Only issue I had was in the reassembly of the auger unit, wasn't quite sure of the blades etc. and the proper order Saw the sketch on your site and figured it out from that. Will visit you guys again when I need a part. Good delivery and timely. Thanks and regards Gil

First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic door jamb putting the new unit in but other than that all is well and functioning well.

I don't know exact details. My husband replaced parts while I held the door.

We removed connections for the door on the bottom (propped up on books). We installed the new cam, the old one cracked and broke, and the new shim and the door is now even with the top of the fridge. It was not before, and the seal near the bottom of the fridge was not solid. Now it is. It was very easy.

Removed everything from the refrigerator door. Removed the screw holding the cover over the top hinge. Removed the two (8mm) bolts holding the top hinge to the refrigator. Removed the door. Removed the plastic grill/cover and the two (8mm) bolts from the lower hinge assembly. Installed the new hinge assembly. Replaced the closing cam (included in the hinge assembly kit) on the bottom of the door. Put the door back on the lower hinge. Installed the upper hinge. Adjusted the door and tightened the bolts on the upper hinge, and replaced the hinge cover. Done!

I replaced both lower hinges without removing the doors. First a couple of observations. The hinge kit consists of two parts; the lower part (bolted to the case) consists of an “L” bracket with a plastic cam, and the upper plastic cam (attached to the door). For some reason the upper cam is available as a separate part . If both cams are plastic both are worn out. Don’t bother ordering the individual cam. If one hinge is worn out the other probably isn’t far behind. Consider replacing both at the same time. Examine the door check. It is an inverted “T” shaped bracket bolted to the door that also holds the door cam. The crossbar of the T are metal tabs that check the door swing. Way too fragile IMO. On mine the refrigerator side was cracked and broke off when I removed it. Since the stops are the same right and left. I just swapped them when I replaced the hinges. Saved $22. Replacing the hinges without removing the doors. {Warning if this technique goes wrong you will be stuck with a loaded door you can’t open.} Remove the vent grill. Stack three 2x4’s along the bottom of both doors ( 26” is about right ). Shim the door(s) up to compensate for the cam wear. About 1/8”) Use a 5/16 socket to remove the hinge from the case. Pay attention to placement of the shims and spacers. Then remove the door cam and stop bracket. Install the new door cam. Leave the screws a little loose. Replace the lower hinge and tighten the screws. Do both sides. Then carefully remove the shims and 2x4’s. Finish tightening the door hinge screws. Check the door swing. I used this technique twice. One to replace the refrigerator side hinge, then again to replace the freezer side hinge and swap the door checks. There were no problems and I saved the hassle of unloading and removing the doors.

Removed the door by removing the top hinge and lifting it off the broken bottom hinge/cam assembly. Removed the broken hinge/cam assembly found out why the cam broke the doorstop was bent so I had to order the doorstop also. The ordering of the parts was so easy. They shipped them on Monday and they arrived the next day. I will use Parts Select again

Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door now self closes .

Each rail required removing two screws which were used to install the new rail. Each one took about 5 minutes however cleaning the recesses was the most effort.

Remove ice maker out of fridge; remove 3 screws
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"

First removed the old sliders, then screwed in the new sliders, replaced all four within minutes.

Turned off water to ref , removed bottom kick plate , got a towel and disconnected the water line plastic fitting and un screwed the (2) tube clamps un screwed the coupling and ((carefully )) slid out the tube from the compression ferrels ! ( Be careful and do not break or distort them + remember exactly the order they are removed ! Slid the protector spring shroud from the plastic tube , took ogg the top hinge cover then remover the top hinge . Carefully lifted the door off feering the plastic tube through the bottom hinge with my foot ! Got the door off removed the bottom hinge + put the new on on, then removed the door cam which was broken on the bottom of the door , lifted the door up and carefully fed the water line through the new bottom hinge . Attached the top hinge and reassembled the rest same as I had dissambled it . Turned on water ( checked for leaks ) ! All working 100% a-ok ! This company is the best ! Ordered the part at 1 pm and had the part at 2 pm the following day many thanks : )

Got the part in and needed two screws to installed on left side. Service was great on the part as it was delivered in 3 days from the time we ordered. Thanks for the quick service

Emptied the drawer and removed it. Then took off the old slide rail. Then I got some hot soapy water and cleaned the walls of the refridge while I was down there and had everything out. I then installed the slide rail put the drawers back in loaded the fridge and sat back and said I just saved myself about $200.00. You guys are awesome we got the part 2 days after we ordered it Thank you for the great service.

Tony The Birdman

First I took everything out of the fresh food door, then I removed the top hinge cover using a philips head screwdriver, and a nutdriver for the two screws holding the upper hinge. Lifted the door off the bottom pin, and placed it on the floor. Then took off the bottom hinge and used the Dremel tool to grind off the rivet holding the broken door cam on the bottom hinge. Used a nut and bolt to hold the new cam in place, and put the lower hinge back on. Then replaced the other cam on the bottom of the door itself, using the nutdriver. (Be sure to buy two cams, and have the bolt and nut to replace the rivet). Reinstalled the bottom hinge, put the door on, replaced the top hinge, and presto! Works great! Thanks to the others on this site for their stories - really helped make it an easy and quick repair!