PFIC1NFWW General Electric Refrigerator - Instructions

The problem began when freezer thawed and could not keep food frozen. Initially, I thought the issue was the defrost heater (because I had seen similar symptoms previously and resolved the issue with a new defrost heater)and I replaced that part with a spare that I had puchased previously. The issue was still unresolved and I noticed the evaporator fan was not running in the freezer because it would not turn on when I closed the door. I checked to make sure I could hear the compressor working (and it was)and concluded that the evaporator fan motor was not running. I ordered the part and found a YouTube DIY video on how to replace it. While I was at work, my fiancee took it upon herself to watch the installation video and install the new evaporator fan motor and all is well.

I looked up appliance on internet,diagram only showed the inlet valve and ice maker in schematic.I ck'd to see if water was getting to valve(it was)but wasn't getting to ice maker,thus I replaced the valve and it solved the problem.

I had replaced the sensors, thermostat and evaporater heater without correcting the problem. Decided to try the control board. The main problem has been the ice in icemaker melting every couple of days and thawing all over the freezer food. The top part of the freezer compartment thawed with less thawing in the lower section. Removed back metal cover. Unplugged fridge, took picture of control board to remember locations of connections. Never needed it though as I took caution to remember the different connections. Unplugged all of the connections and then took needle nose pliers to depress the 4 pins holding the control board in place one at a time. This was a bit difficult and you will need to exercise patience. Not my long suit. Eventually I depressed the pins correctly and got the old control board to slide out. Replaced with new control board and re-connected all the wire harnesses. They actually slide on pretty easily if you have them in the correct position. I also had taken all the food out of the freezer and removed the cover to the evaporator which was iced up. Took a hair dryer and thawed all the ice before re-starting the fridge to give it a nice clean start. Replaced the back panel and plugged in the fridge. 4 days now and it is running great so far. A lot quieter than before.

Ironically I did this today, as this email request came up asking how it went. I'm not a repairman, I'm a software engineer, and I can't thank this site enough for the step by step videos. With the video to help, this was a breeze, I was nervous as I had to empty all my freezer out onto the living room floor. Once that was done the repair took about 30 minutes. Thank you partselect!!!!! My second time doing business here, and I'll be coming back (well, if something breaks, so let's hope I don't have to).

it was easy the only thing was i had to cut old harness to remove 2 wires that went to coil that had to go back in the new harness other then that a peice of cake.

removed the inside fridge electrical panel and swapped switches

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

Connected the 2 wires and pushed in the switch until it clicked.

snapped right in place

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

No need to shut off the water supply. A pair of pliers was required to remove the old filter, and the new one went in with just a quarter turn. It locked in place with no water drips. Less than 5 minutes to install.

This was SOOOO easy and the people at PartSelect were extremely knowledgable and helpful. I am the woman of the house and ordered this part and installed it myself. No problems!

It was very simple , just follow the instruction given by partselect , it took about 15 min to install new control board

easy pry out, disconnect wiring, connect on new switch and press in switch.

Pressed the button, took out the old, put in the new. :)