TBJ14JABLRWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from Philadelphia, PA
- Parts Used:
- WR12X10107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator door handle broke
Simply removed the screws and pulled the old handle off and aligned the new handle with the holes and replaced the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from TWIN FALLS, ID
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Interior light needed replaced
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from BELLEVUE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from Burke, VA
- Parts Used:
- WR51X444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Defrost Heater failed due to old age ?
Removed plastic covers and used a nut driver to remove the two screws that held the heater assembly to the freezer coils, disconnected wires from old assembly, connected wires to new assembly, replaced mounting screws and replaced plastic covers and secured them with the original screws. All in all, a fairly easy operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Brookfield, IL
- Parts Used:
- WR71X2086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no shelf in my freezer
first I ordered parts that didn't work. the return process was painless and I found the part I needed, which just popped right in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Clinton Twp., MI
- Parts Used:
- WR32X10340
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the plastic vegitable bin cracked
even my three year old grandson could do this one! open the door slide the old tray all the way out and slide the new one in. wha-la! Actually I was very impressed at the ordering process since I could actually see a picture of the bin in its actual use not just some obscure number with a vague discription. I'm a visual person so this made it extremely easy to see what I was ordering. No guess work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Rome, NY
- Parts Used:
- WR71X2086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a shelf
My repair was simple. Just put the shelf in the holes in the freezer. The AMAZING thing was how quickly I recieved the part after placing my order. I placed the order at about 3:30 pm on a friday checked the box for ground shipping and the part was at my door the next morning. I think that was a mistake, but I was impressed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paula from KEY BISCAYNE, FL
- Parts Used:
- WR51X444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
Defrost Heater too old
I disconnected the old defrost heater removing 2 small screws and the electrical connectors, afterward I attached the new part, reconnecting back the electrical connectors and screwing the removed 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boris from East Lansing, MI
- Parts Used:
- WR12X10108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no problem
easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Owls Head, ME
- Parts Used:
- WR32X10500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken crisper drawer support
quick and simple--removed the old one and slid new part in on same support pins.I had the new part via UPS LESS THAN 24 HRS.FROM THE TIME I PLACED THE ORDER! THANKS, SOMEONE IS REALLY ON THE BALL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Danville, CA
- Parts Used:
- WR12X10107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The beyond cheap GE handle broke on our rental unit GE refrigerator after less than six months
The new handle just took three screws matching our model refrigerator perfectly--and it is much sturdier than the original. We originally went to the GE site and they wanted $70 +shipping for the same handle. Our landlord only paid $500 for this fridge six months ago--brand new! For a total of just under $17 we got a new handle in perfect condition--delivered quickly to our door. It was exactly as described and fit our model perfectly. We couldn't be happier and will tell all of our friends about this wonderful site. Thank you!!
Was this instruction helpful to you?
Thank you for voting!