MSX25DPBAWW General Electric Refrigerator - Instructions

Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.

I removed the plate covering the water valve for the ice maker and water dispenser, removed the nut holding the 5/16" tubing to the valve and took off the tubing and nut. I did not need to turn off the water supply or unplug the unit. I removed the kick panel in the bottom front of the refrigerator, replaced the existing plastic fitting with a new push-on fitting, then spliced the tubing coming from the water chiller to the valve where the leak was thus bypassing the broken tubing with new tubing. I reassembled the valve using the original plastic compression nut, replaced the cover and ran the water dispenser while checking for leaks. The water dispanser works great with no leaks.

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

Part was perfect fit .Removed fan .three screws.replaced that s it

Since I really needed to replace the deteriating auger I used the original ice bucket and transferred the new auger assembly into the old ice bucket. Looked complicated at first, but make it work and my refrigerator is now making nice clean ice. It would have taken a lot longer if I sent the new bigger ice bucket back and it was my fault. With the videos and pictures on line made the replacement of the auger & ice bucket easy. Thanks Bill

the previous left behind a side by side, everything worked however the auger in the ice bucket was a little rusty. I wish that I could say it was all me but the truth of the matter was the videos on file.

They were nicely done and easy to follow as I took the unit apart and replaced the auger in about 30 minutes. Thanks for all your help in part look up.

Opened, discovered not flapper but more complicated

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

Turned water supply off; pressed dispenser sw to release presure ; cut tubing holding reservoir ; nuit driver to release screw holding reservoir and pulled out ; took outside and used hose nozzle to try to clear; did not clear at first then took weedeater string and disloged something and water flowed freely; turned out had to change waer solenoid valve (both) as the one for the water dispener was also plugged which did not show up before.
P.S. Had back flow water thru system before and changes of parts. Water flowed freely.

Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.

Remove the burned out bulb and install the new light bulb.

replaced the broken one with the new part

There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great

I simply removed 6 screws that held bucket to face and pit on new bucket and put it back in freezer works great