TBT19PATERWW General Electric Refrigerator - Instructions

I pulled out the shelf and removed the 2 screws holding the broken side rail to the shelf frame. I then screwed the new rail in and set the shelf back in.

Unscrewed four screws, two on each part, and replaced broken parts, reinserting screws. This is a no-brainer repair.

Basically I removed 4 screws holding the rails together, did a little cleaning of the existing parts that I would re-use and screwed the 4 screws back in and put it back into the fridge. Piece of cake. If I hadn't cleaned up the old parts it would have taken me 5 minutes.

removed produce drawers, removed center piece front cover, removed glass shelf, removed broken drawer slide rail - unscrewing where attached in the rear of the refrigerator. Also removed screw from centerpiece where broken drawer slide rail was attached. reassembled all very quickly....saved myself having to buy another refrigerator by doing this simple repair.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

I had one of my guy friends do it for me. It took him less than 10 minutes, and probably would have been quicker if he had a better screw driver. Mine is a cheap girly one that he could not get a good grip on.

The bottom shelf of my Mom's fridge broke. I found the part I needed and went to repair it. Realized both sides were broken. Ordered other side as well. Two screws in front, two screws in back. Front side had a metal strip covering screws. Had to pull that off to get to screws. Snapped back on after repair.
Mother was very pleased.
Told her to be careful. Those little pieces of plastic can be expensive.

Both side rails were busted. the parts were precise and it was extremely easy. Thanks again.

Easy

I ordered the part one day and it was in my refrigerator by the next day. No tools required. You guys are incredible. This is the second time I ordered parts from you. You never disappoint!!

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

This was very easy. Just unscrew the broken side pieces and attach the new ones. If the rubber gaskets are still in good shape, gently pull them off and attach them to the new rails. I was very impressed with the service from Partselect.com. I gave them my appliance model number and they helped me find the right part. I ordered on Sunday evening and had the parts in hand by Tuesday. Great service! I will definitely use this company if I need more parts.

I took out all the stuff on the shelf, and the drawers.
then I took out the shelf, pulled off the cover so I could get at the screws.
I unscrewed 2 screws, threw out the old part, and screwed the new one into the shelf.
then I put the whole thing back together, in total the hardest part was cleaning off the shelves and then putting everything back in.
As a note, there was a gasket on the old rail that was not on this one. I had some silicone tabs that I used instead, but I really think the gasket should have been part of the order.

Removed the broken rail (2 screws), replaced the new rail (2 screws), reassembled all in about 8 minutes. It was AWESOME!!! I had spent hours trying to repair it and, fortunately, gave up and decided to look online for the part. Didn't even think that the part would still be available. Not only was it available but it arrived in 2 days! Anything that is broken in the future: I am going to your website first! Thank you!!!

The entire frame that holds the two crisper drawers pulls right out. After that, it's just a matter of unscrewing the broken part, snapping in and screwing the new part and sliding the whole thing back in.