TPK24PFBBAA General Electric Refrigerator - Instructions

After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...

Snapped off the plastic plate covering the dispenser. Removed the four screws holding the mechanism in place. Remove the electrical connections. Pull the mechanism out and up carefully pulling the dispenser pad out with all the mechanism in place. Look at the mechanism before removing any parts to get a mental image so that reassembly will be easy. Remove any electrical switch or circuit boards and remove old parts before submerging the mechanism in hot soapy water for clean-up. The Clean-up will take longer than the disassemble and reassembling. After completion the dispenser works as it should.

Seemed simple and intuitive B U T the water tube receiver fooled me. Seemed to be on backwards. So, like my wife suggested, I D I D then read the installation instructions. Yeah! It's amazing what you can do when you just RTI. :-0

I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.

Took out one hex screw, disconnect electric couplings, pulled original ice maker out and found that the water supply line to the ice maker was frozen solid as well as the shute cup. Used hair dryer to thaw out the line and the cup reinstaled old ice maker and it worked fine. Did not have to use the new part at all at this time. Am keeping new part for future use.

took 1 screw out and removed ice maker and slid new one in and replace screw and connected power cord

Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!

Went to GE website and researched the problem for the model, determined that it was 90% sure it was the Ice maker, I ordered it and it arrived the next day, installed it and it began working immediately,

Watched the video from your site and followed instructions, extremely easy after that.

Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.

Super easy, had my 15 year old do it (with my supervision).
Followed very clear Instructions that come with the replacement...
But, he could not get to the plug location until he removed 4 screws holding the motor assembly that spins the ice in the drawer and moved it out of the way...
Followed the rest of the instructions...
Works like a charm.

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.

Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.

Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.