TBX21DKGR General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Interior Light did not go on due to faulty switch
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from RNCHO CORDOVA, CA
- Parts Used:
- WR07X26748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Does not start , trips breaker
I pried the relay from compressor with small screwdriver, cut and replaced burnt wire going to relay,pushed new relay on compressor and wires unfortunately it did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from OZARK, AR
- Parts Used:
- WR9X483
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
freezer compartment worked fine but very little cooling going to refrigerator section.
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The replacement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
switchlight on my refrigerator was not working
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arnold from Lighthouse Point, FL
- Parts Used:
- WR17X11773
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door shelf retainer was damaged
I removed the original retainer and installed the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly A from Columbus, OH
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end cap to bar of freezer door broke
Snapped end cap onto bar and installed bar onto freezer door.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from carmel, NY
- Parts Used:
- WR60X123
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Not cooling and freezer freezing up
I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marnie from Denver, CO
- Parts Used:
- WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
a fan blade broken causing it to make a loud noise
we took off the old one and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruchik from Bronx, NY
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf retainer bar end cap.
I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before ordering. Otherwise, the entire process from order to finish took about 3 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kaye from San Francisco, CA
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I didn't know if I could get a replacement part, but I googled "replacement parts" (or some such), and since this website looked easy to navigate, chose it. (Actually, I did my ordering via telephone). The sales rep. helped me clarify which part I needed, I ordered it, and received the part the very
I simply snapped the two end pieces into place, attaching the guard rail. It was like putting the pieces of a very easy puzzle together‚ especially for someone like myself who is mechanically challenged.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from North Quincy, MA
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old end cap broke.
Put the new end cap on and snapped it into place, took about 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Northglenn, CO
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The above door End Cap broke.
The repair just required snapping the new part on to the door shelf and then snapping the shelf in to the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from CENTRALIA, IL
- Parts Used:
- WR23X37285, WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light kept blinking on and off never same way
turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CLIFTON, NJ
- Parts Used:
- WR60X187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Fan would not turn when the refrigerator came on all the time. Would physically have to turn the fan blades.
Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from LAPORTE, PA
- Parts Used:
- WR60X30349
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
freezer too cold and refrigerator not cold enough because fan not working
Had to defrost a bit and then was able to remove rear freezer panel by simply removing the 2 screws holding it in place.
Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and red wires clipped from the old motor. Then reinstalled.
The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.
Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and red wires clipped from the old motor. Then reinstalled.
The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.
Was this instruction helpful to you?
Thank you for voting!