TBX19PAYARBB General Electric Refrigerator - Instructions

Removed the broken end cap, replaced and secured it. Put items back in the door shelf.

This was very easy. Just unscrew the broken side pieces and attach the new ones. If the rubber gaskets are still in good shape, gently pull them off and attach them to the new rails. I was very impressed with the service from Partselect.com. I gave them my appliance model number and they helped me find the right part. I ordered on Sunday evening and had the parts in hand by Tuesday. Great service! I will definitely use this company if I need more parts.

looked up the part, ordered it. 2 days later, popped it in...less than 5 seconds...DONE....great website and customer service....very descriptive and informative for the novice and experienced repair person alike.....Thanks!!

Remove bottom glass shelf, lift up -then remove entire drawer slide assembly.Remove plastic decorative front cover(it just snaps off) and unscrew left side drawer slide screws.replace with new part and screw in screws. Replace in bottom of fridge and replace glass shelf.So Easy that an average house wife like myself was able to do it alone.Almost as easy as finding the part needed on partselect.com! Thanks, it was much easier than apple pie.

The entire frame that holds the two crisper drawers pulls right out. After that, it's just a matter of unscrewing the broken part, snapping in and screwing the new part and sliding the whole thing back in.

Removed two screws, lined up the rail and replaced the screws. That was it!! Glass shelf sat on top and bin slid in smoothly.

Pulled out old drain gromet. Have to be careful not to put drain in motor. Experienced repair person could probably to in 5 minutes; it took my husband about 15 minutes. Did not really need entire drain line; just connection at top.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.

Your online helpful hints made it easy as pie.

Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.

The hardest part was figuring out the part needed from so many little pictures. The actual repair, a piece of cake!

Sears told me the part was no longer available. I came to your web site and then called your customer service. A very nice customer service lady helped me find the part. Very simple to pull the old one off and reinstall the new one with a rat trap behind the unit. Just in case it came back. Could have been a client but probably was a rat. Thanks for the great service.

take fan out,put new in

Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I ordered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.