TBEA25FRDAD General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James U from Pawleys Island, SC
- Parts Used:
- WR72X287
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
part did not fit.
was able to grind the edge to map it fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jady from Thornton, CO
- Parts Used:
- WR49X10183, WR2X4139
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Not clear instructions
Common sense will take you thru the process of removing, then just reverse the process to replace the auger.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from Marshall, WI
- Parts Used:
- WR17X2769
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right vegetable drawer slide rail broken
The repair is somewhat self-explanatory. The old/broken rail which was broken needed to be unscrewed in front and rear, and the new one simply inserted and screwed in. Simple installation. What I REALLY wanted to share, is how impressed I was with the FAST service/speed that the parts arrived. Originally, we thought that just the middle drawer slide needed replacing, so I ordered the middle one and installed it. After installing it we realized that the right slide was broken too, so I ordered that. I placed the order on Saturday and the part was delivered to us on Tuesday!!! SUPURB service!! I will DEFINITELY order my next parts from PartSelect again!! Thanks for wonderful experience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Country at from SAYRE, OK
- Parts Used:
- WR55X24065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
A power surge made my side by side refrigerator stop working
I started at the compressor and replaced the overload and the Ptcr first and that did not make the compressor start running again, so I replaced the capasitor and it still did not start, so I bit the bulett and replaced the Main Control Board and that is what I should have checked first, when I removed the old one I found a little burnt spot on the back that I could not see from the front. The new one did not look exactly like the old one, it had two more wire terminals than the old one, but just leave them blank and everything will work just fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Spring, TX
- Parts Used:
- WR62X23154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator was only dispensing crush ice and not cubes
Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Morris, IL
- Parts Used:
- WR55X24065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Compressor not coming on
Had to e-mail GE for electrical schematic. Checked voltages to compressor. Jumpered compressor to see if it would even come on. Found bad run capacitor. Fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Pawling, NY
- Parts Used:
- WR17X2769
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Slide rail was broken
Unscrewed the old rail, cleaned everything and installed the new rail
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- theodore from salisbury, NC
- Parts Used:
- WR60X30349, WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
bad fan motor
take fan out,put new in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Villa Rica, GA
- Parts Used:
- WR2X4550
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The drive cup was old,worn,slipping and appeared to have never reached deep enough.
I removed the front of the unit assembly and removed the entire auger unit and drive assembly. I married the old drive cup and new drive cup back to back using vise grip pliers, drilled 4 3mm holes, installed 4 phillips head stainless steel screws and, using an emory wheel, ground off the exposed screw ends. I then re-installed the drive assembly and auger unit. This increased the length of the drive cup allowing the drive to fit without any slippage. The entire cost was less than $18.00 including shipping and screws and took about 1 hour. It works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Williamsburg, VA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new light socket
Pulled out old socket.pushed in new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ravenden, AR
- Parts Used:
- WR2X4550
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Put the part in and observed water leaking from the ice maker which caused the cup to break
Ordered new Ice Maker from you and fixed the problem completely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keven from Fleming Island, FL
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
right side slide rail broken
pull the front cover off, take the two screws out and the side rail comes right off, put the new one in place, put the screws back in and bang!.....all done. Took longer to take the stuff out of the fridge than to make this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from St Louis, MO
- Parts Used:
- WR17X2770
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drawr slide broke
followed instructions from video on your site
Was this instruction helpful to you?
Thank you for voting!