TFF-19DV-C General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- paul from Arlington, VA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The Door hinge cam broke apart
Discovered the door cam was broken. Did a search, found the part on PartSelect.com. Read the repair stories and realized I need two cams. So I just bought the whole hinge assembly figuring it would be a little easier and did not cost that much more.
Put blocks under the door, unbolted the old hinge from the refrig, and the old cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.
Put blocks under the door, unbolted the old hinge from the refrig, and the old cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Bath, MI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dorr would close properly
Lifted the door while closed into position even with freezer door. Then put srap pieces of wood under door to hold into place while I removed the old hinge assembly and replaced with the new one. The door works good now. Make sure you replace both peices as they will both be worn.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Micheal from Longwood, FL
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Door dropped on the refrigerator side.
Removed all items from the door shelfs.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now level with the freezer door.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now level with the freezer door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Woodstock, GA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door would not close properly.
Removed door and replaced bracket assembly. Door works like new. Self closing and sealing properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rocklin, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door sagged and would not stay closed
Don't even need to empty the shelves in the door.
Just prop the door up with a block of wood from the floor to the bottom of the door. Lay on the floor and replace the parts.
The door was acting up for a long time. I wish I had researched and repaired the problem a long time ago. Now it works great!
Just prop the door up with a block of wood from the floor to the bottom of the door. Lay on the floor and replace the parts.
The door was acting up for a long time. I wish I had researched and repaired the problem a long time ago. Now it works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Waterford, MI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door closing cam desintegrated
Took the stuff out of the door
Removed the door
Replaced the hinge
Put the door back in
Put the stuff back in the door
You may be thinking that I'm not much for words - but this was SO EASY that it doesn't warrant using more words than I did.
My 7-year-old son helped me - it was a fun father-son project.
Removed the door
Replaced the hinge
Put the door back in
Put the stuff back in the door
You may be thinking that I'm not much for words - but this was SO EASY that it doesn't warrant using more words than I did.
My 7-year-old son helped me - it was a fun father-son project.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- henry a from pennsauken, NJ
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
bad door hinge and cam
parts ordered fit perfectly made repair removed items from shelves removed door avd replaced hinges and reassembled 1/2 hour total by myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zach from Glenwood Springs, CO
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door wouldn't close and open properly
Removed guards and covers, (2 snap connections, 3 phillips head screws) Removed two 5/16" screws, removed door, removed cam from bottom of door, installed new items.
Worked Great!!!
Worked Great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Austin, TX
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The cams that allow the fridge door to automatically close had worn out
First I bought the right tool to remove the hinges.
Then replaced the hinge with the two cams.
Now the door closes itself.
Then replaced the hinge with the two cams.
Now the door closes itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Warren, VT
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Plastic cam at the bottom of the door disintegrated so door won't shut
1.Emptied the stuff from inside of the fridge door.
2.Using a phillips screw driver I removed the plastic cover over the top hinge.
3. Using a small ring spanner I removed the two bolts holding the top hinge (pin), removed the hinge and lifted the door off the bottom pin.
4.Using the same spanner I removed the bottom hinge containing the broken plastic cam.
5.Replaced the broken hinge with the new one and put a little grease on the hinge pin.
6.Placed the new plastic cam on the hinge pin and refitted the door.
7.Replaced the top hinge and plastic hinge cap, Job Done!
A couple of points a) When your plastic cam needs replacing, always buy the hinge pin & plastic cam. The pin has a plastic cam welded to it and as this is the partner of the plastic cam it will also be worn so you should replace them as a pair.
b) You will spend more time cleaning the 'out of the way' parts of the fridge than actually carrying out the repair.
My fridge is now as good as new.
2.Using a phillips screw driver I removed the plastic cover over the top hinge.
3. Using a small ring spanner I removed the two bolts holding the top hinge (pin), removed the hinge and lifted the door off the bottom pin.
4.Using the same spanner I removed the bottom hinge containing the broken plastic cam.
5.Replaced the broken hinge with the new one and put a little grease on the hinge pin.
6.Placed the new plastic cam on the hinge pin and refitted the door.
7.Replaced the top hinge and plastic hinge cap, Job Done!
A couple of points a) When your plastic cam needs replacing, always buy the hinge pin & plastic cam. The pin has a plastic cam welded to it and as this is the partner of the plastic cam it will also be worn so you should replace them as a pair.
b) You will spend more time cleaning the 'out of the way' parts of the fridge than actually carrying out the repair.
My fridge is now as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vickie from Chandler, OK
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Refrigerator hinge broke
Use several wood blocks and propped fridge dooe up and someone else steadied the door while I replaced the hinge. Pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from lesage, WV
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door stop broke
they sell the cam piece but the instructions says not to replace only one part. so beware you need both the cam and hinge as a kit .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Holbrook, NY
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door closing cams, top and bottom, became damaged and needed replacement
Turned refrigerator off. Removed food from right hand (refig.) door. Closed door. Removed upper hinge cover with a standard Phillips screwdriver and then removed upper hinge by removing two 5/16" bolts using nutdriver. Lifted door up to clear the bottom hinge-post and set it on the table. Removed the kick pan at the bottom of the refrigerator and then removed the bottom hinge-post which was attached with two more 5/16" bolts. Installed new lower hinge post and rubbed a small amount of mineral oil on the closing cam (which is riveted to the hinge-post). Removed the old upper closing cam from the door (5/16" bolts) while it as lying horizontal on the table and installed new cam lubricated with a small amount of mineral oil. dropped the door in place, replaced upper hinge and cover. Replaced kick pan. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Colfax, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Hinge assembly spacer at bottom hinge failed breaking up in small pieces
Followed other messages to complete fix. Simple overall.
Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.
Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.
Was this instruction helpful to you?
Thank you for voting!
Drawer slide rails worn out
The new slides were slightly different than the original slides. The slides fit, but the glide inserts on the slides interfered with the drawer. I had to remove the glide inserts, and modify them. Now the drawer slides properly.
Was this instruction helpful to you?
Thank you for voting!