TFF-19DV-E General Electric Refrigerator - Instructions

Thought I would only need one when I looked at the picture of the parts. Decided to order two just in case and after taking it apart both were broken. Needed two.
Took the top door bracket off and lifted the door off of the bottom bracket. Re-assembled cams, put a little white grease on all moving parts, placed the door into bottom bracket and installed top bracket. Adjusted top bracket to make door line up with edge of refrigerator and all is well.

completely removed door, then replaced worn-out cam on bottom of door-simple enough; then removed hinge from bottom of refrigerator; removing old cam required drilling out the rivet that fastened cam to hinge; secured new cam to hinge with small machine screw and nut. This procedure is relatively easy but does require minor mechanical ability and having a small drill and bit set. However, replacing the two cams totally fixed the problem.

Door closing cam was disintegrated, and the matching cam on the hinge assemble was worn too. Replaced the Door Closing Cam, along with the hinge assembly, and door closes fine now.

Use several wood blocks and propped fridge dooe up and someone else steadied the door while I replaced the hinge. Pretty easy.

Replaced the old cams with new ones, door works perfect now.

The bottom of the door was 5 " off the floor. A 2x4 block and a 4x4 block were pushed under the door and supported it while the water line was disconnected the hinge removed and the cam replaced. It was a simple fix and reading other people's experience made the repair so much easier.

Turned refrigerator off. Removed food from right hand (refig.) door. Closed door. Removed upper hinge cover with a standard Phillips screwdriver and then removed upper hinge by removing two 5/16" bolts using nutdriver. Lifted door up to clear the bottom hinge-post and set it on the table. Removed the kick pan at the bottom of the refrigerator and then removed the bottom hinge-post which was attached with two more 5/16" bolts. Installed new lower hinge post and rubbed a small amount of mineral oil on the closing cam (which is riveted to the hinge-post). Removed the old upper closing cam from the door (5/16" bolts) while it as lying horizontal on the table and installed new cam lubricated with a small amount of mineral oil. dropped the door in place, replaced upper hinge and cover. Replaced kick pan. Done.

I did not realize I needed 2 cams to complete repair. Door cam was riveted in. I had to drill out rivet and replace with nut and bolt. Otherwise it went quite sommothly. At first I just replaced the cam on bottom of refridgerator but door was not quite right when closing. Further inspection showed the door had the other half of cam that also needed replacement. Needed 2 orders. Paid for 2 shippings.

removed broken rail and replaced two screws and the job was complete...took longer to clean the botom of the refrigerator than replace the part

Used (2) 2 x 4's as block and lever to raise door removed 2 screws and removed door used same socket to remove and replace door side of replacement part. replaced door. This is the second time I have replaced this part on frig. side. Very easy replacement.

I pulled all the items out of door, removed door top hinge cover, lifted the door off the hinge and removed the bottom hinge and closing cams and replaced them and re hung the door, just about that fast.

PS
Thanks for the parts

I am a widow, 70 year old. Ordered parts. They came very fast. It took less than Fifteen minutes to remove door and take off broken parts and put the new ones on. I am glad I have two doors on the fridge so I was able to lift it up.

My wife and I gave an old, but really good refergerator to our son (a Major in the Army). Upon taking it into his house he had to remove the doors of the refergerator. While he put the doors he lost the "cam" for the door, making if difficult to close (actually had to lift the door up and then close it). I ordered the replacement part, and unless I am mistaken, it arrived the same day. I still cannot figure out how this happened, but it was great!!

Replaced both upper and lower cam's. Removed door from refrigerator, removed bolts on door cam on bottom of main door and replaced cam, then removed bolts from door hinge assembly, drilled out rivet holding on cam, replaced with new cam and re-riveted.

After watching your instruction video and not wanting to shut down refrigerator and remove foods from door, I elected to lift the door and place blocking under it.The actual hinge replacement took approximately 10 mins. I would also like to say that I am extremely satisfied with PartSelects handling of my order and your promptness resending my order because of my goof-up with my own address. I am grateful and will recommend you to anyone who needs parts for any appliance. Thanks again. Chuck Gjovig