PDF22MFSW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Fred from Crawfordsville, IN
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
No water to icemaker
Shut the water off, removed two screws,removed the inlet, from the water valve then the line from the valve to the ice maker. Then you reverce these steps and you are done. The shipping time was the best I have ever seen. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Eugene, OR
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door activated light switch was missing.
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Lake Helen, FL
- Parts Used:
- WR57X10033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Mounting bracket did not fit. Retainer for water input looked like a thread protector.
Put bracket on workbench and hit two or three times with hammer. Glad I did not remove water inlet retainer from part, it can very easily be mistaken for a thread protector.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larrie from punta gorda, FL
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
ice maker just stopped
part arrived on schedule,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lana from Fort Myers, FL
- Parts Used:
- WR29X10092
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The fill cup kept breaking and we couldn't find the part. Did a google search and found Partselect.com who had it.
Slide it over the fill hose and just line it up and put it in the slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paulette from Crandall, GA
- Parts Used:
- WR57X10033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Had never installed one before and was not sure which was top or bottom. The piece was made different than the original
Unhooked power to valve
Removed old valve by taking out 2 screws.
Used adjustable wrench to remove water lines. Then reversed and hooked everything back up
Removed old valve by taking out 2 screws.
Used adjustable wrench to remove water lines. Then reversed and hooked everything back up
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Sylva, NC
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bad switch for door prevented interior light from coming on
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- olin from forest city, NC
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker not working
First i shut the water valve off going to the fridge, I then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then i took the water line loose to the element, reverse the prosses and put all back on new element and installed,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from Fort Myers, FL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
light in freezer section not working
Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Swansea, MA
- Parts Used:
- WR02X11684
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
middle rail cracked
look at how part was in before you take it out - I didn't and it took me three times longer!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Searle A. from Lincoln, ME
- Parts Used:
- WR50X10047
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Refrigerator & Freezer not defrosting
Replaced thermodisk (Fuse-M). Did not solve the problem. Found Burn Mark on Mother board. Replaced Motherboard. Freezer still frozen. Waited 17 hours never defrosted. After 17 hours defrosted freezer and now waiting to see what the refrigerator is going to do about defrosting. There is continunity through the thermodisk and the defrost coil.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Oviedo, FL
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Ice Make Not working
I monitored the ice maker after it stopped working and noticed it was not filling with water. I loosened the water feed hose to the single valve outlet and the water feed was fine. However, the single valve outlet never activated to turn on the water feed. I disconnected the waterfeed and electrical connection from the single valve outlet and removed it. Replaced it with the new one, reconnected the water feed valve and electrical connection....allowed the ice maker to cycle and it started filling the ice maker with water right away. The unit is functioning fine now. Thanks to Select parts for filling my parts order fast and accurately. Regards.....E. Tew
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brandon from Bruceton Mills, WV
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Defroster stopped working and iced up evaporator coil
I have a GE Profile French door refrig. It's only about 4 yrs old and the defroster stopped working. I read the other repair stories and was able to narrow it down to either the temp sensor, defrost timer, or main board. The refrig section was up to about 47 degrees and freezer was around 25. I could tell it was trying to cool but couldn't. So I tried the temp sensor first. I cut and spliced the new sensor on the outlet of the Evap. Coil and it took about 15 mins. Turned refrig back on and waited. The coil started to ice over after about 5 hrs I left the back panel off so I could see if and when then heater kicked on. After about 8 hrs I looked in and saw a faint glow and water trickling down and running out the drain. Turned out the sensor was bad and wasn't telling the main board it needed to defrost. I would try the sensor if you are having the same issues before spending a lot of money on the main board, defrost heater and or timer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Jasper, GA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Water overflowed into ice cube resevoir when filling cube tray
Move unit out to access rear. Unplug unit. Shut off water supply. Remove lower cover with phillips screwdriver. Remove valve and both water lines. Install water lines back into new valve and install valve back into position. Turn on water supply and check for leaks. Install cover. Plug unit back into wall. Let icemaker produce some cubes to make sure everything is working correctly before pushing unit back into position. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from silver bay, MN
- Parts Used:
- WR55X10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Fridge Side Freezing/Too Cold
Followed the repair video, was spot on!!
Was this instruction helpful to you?
Thank you for voting!