PSB48LGRB General Electric Refrigerator - Instructions

Turns out it was only the frozen water that thawed when I unplugged the fridge for 24 hours.
New part returned, not used.
Service was excellent.

instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.

Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable should be more flexible and adapt to the fridge a little more friendly.

My father called and asked me if I knew where he could get a new switch light for his refrigerator. I came across your web site and found the part right away. In less than 3 days the part came and my father put it on. He said it was easy and that it was great to have the part come to him instead of having to search all over town. Thanks so much for the fast, easy service.

I located the light switch at the bottom of the area where the door closes. I just popped it out with a small screwdriver and installed the new switch. A 2 wire connecter and small clip is all there is to it.

Really simple... broken light switch easily removed with flat edge screw driver. Once removed unplug and plug new one in and good to go.

I pulled the bulb out to see if it was the bulb, no! I took the switch out, of course with the refer unplugged, and jummped out the wires and the light came on. Ordered my switch and put it in in 10 seconds and then there was light! Thanks again for showing me the light!

Tim in NJ

I got the model # off the fridge, ordered the part online. The part was fairly cheap and was at my house 2 days after I ordered it. It was the exact part and I installed it in about 15 minutes and everyting worked out fine and easy and cheap, under $15 total to fix the issue. All I needed to do was use a flathead screwdriver to "pop" out the old switch, remove the 2 wires off the wire connection points, put the wires on the new switch and push it back into place. easy. Great place to get exact parts and fast shipping.

I put the water hoses out the valve and put the hoses back in new valve after that put the valve in the same place with the nutdriver. When refrigerator take the temperature inside, the ice began really easy. Thank you.

I got the wrong switch before so just need to put the right 1 in. Super easy, pop off old, plug in new, click back into place. Done. REALLY REALLY EASY for anyone to do

replaced lights in refrigirator and freezer

Installation could not have been easier!

My GE SideBySide fridge stopped making ice. The green LED light on the icemaker was not blinking. The water dispenser worked fine. Fridge is only 5 years old. Freezer temp set at 7 degrees...fridge at 37 degrees. I have been using these temps since new. GE hotline suggested freezer temp should be at zero degrees. That did not work. Second call suggested an airflow issue within the freezer...there should be 1 inch space between food and back wall. Still no ice. The water valve looks to be the issue. I ordered it and got it in 2 days. Valve is in the back bottom, refridgerator side. Push the white collars around the water hoses...Then pull the hoses out. An adjustable wrench removes the nut for the inlet hose. Disconnect 2 electrical plugs. Be sure to push the water hoses fully into the new valve. I pulled the white collars out a bit to insure a tight fit. I was surprised at how simple this was to install. As it turns out, I was still getting no ice. I ordered a new ice maker and now I'm getting ice. The icemaker was EVEN EASIER to install.

First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic door jamb putting the new unit in but other than that all is well and functioning well.

Remove ice maker out of fridge; remove 3 screws
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"