GSS22IBPAWW General Electric Refrigerator - Instructions

1. Important: First you will need to prepare for water from melted ice. Plug the drain hole in the bottom rear of the freezer. Have plenty of rags near by. A pan or small bucket is helpful.

2. Unplug refrigerator

3. Remove (4) screws (2) w/screwdriver and (2) w/nut driver. You can remove the light cover to get it out of the way but you don't have to.

4. Remove the evaporator cover (The rear wall)

5. Melt and remove any ice build up. Remember those rags?

6. Remove (2) screws from the heater bracket

7. Remove the failed heater. My old heater was a single element. The new heater was a dual element. This made no difference.

8. Disconnect (2) wires.

9. Re-route and reconnect (2) wires. The wires were re-routed because the new heater has both wires on the same side. Not a problem.

10. Install new heater on the bracket (2) screws

11. Replace cover (4) screws

12. Power up the refrigerator

first I removed shelves, bottom drawer, one drawer slide. then removed plastic cover from inside, light bulb, removed two screws from back panel (inside refrigerator, removed panel. You will see heater towards bottom. Remove screws (2) that hold heater in place, disconnect wires from heater, thermostat is
attached to line just above where heater is attached.
You will find that is quicker to cut thermostat wire, then splice together with wire nut. reassemble in reverse order. To check ice door, you must remove inner door panel, mine had to selenoid rusted and locked up. Removed , cleaned, reinstalledm worked ok. Hope this helps someone. Thank you partselect from your good service!

Ref. still worked but had this loud high pitch whining noise coming from inside freezer for a few months. It's probably a bad bearing or motor.

1) Remove all shelves and ice dispencer
2) Remove (x2 screws / a green wire that's clipped on) and the evap cover
3) Remove (x3 screws) cover motor/solenoid and unplug harness
3) Remove (x2 screws) icemaker and unplug harness
4) Remove/Loosen (x2 screws bottom / x2 screws top) Duct air freezer
5) Remove (x2 screws) Orifice evap fan and unplug harness
note: will need to remove right screw to get green ground wire off. And be careful on to damage the gasket.
6) Once Orifice out of refrig, disassemble.
7) Main thing to replace is the Motor DC Evap fan, and maybe CapDust, BumperLid, GrommetEvpFan.
8) now just go in reverse order...
That's it . . . wasn't too hard and NO MORE whining!!! Save at least a couple of hundred by not having a prof. come out and do it. Easy enough for most DIY person.

Removed rear and front grills,brushed and vacuumed area- probably caused the fan motor to fail- unplugged fan, removed fan,motor,and shroud in 1 piece, carefully slipped fan off motor shaft, unscrewed shroud and motor. assembled in reverse order. Frige is in tight area, .I'll now roll it out and clean often

After further diagnosis decided the main circuit board was the likely culprit. Ordered a new one from PartSelect. It came in 2 days and took less than 30 minutes to install. Unplugged the refrig. Removed the old board cover with a nut driver. Removed the wiring cables (note their location on the board) and also there were a couple of cable plugs on my refrig that were not not hooked to anything on the board. Snapped the old board out and the new board in. Reinstalled the cables and then the board cover. Plugged the refrig in and back in business. PartSelect is a great website! The speed of delivery and available information just saved me $500 to $600 from a appliance repair shop.

After advise from the expert, he was adamant the motherboard was the (via symptoms)problem. After receiving the replacement board (via FEDEX), I followed the easy to understand instructions. I did number the electrical plugs and mapped the connections on paper. The key to the rapid fix was to carefully read all of the instructions to verify which (if any) wires needed elimination, which in my case was none. I will definitely use this service in the future as the expense was affordable and after research, I estimate a savings between 55% to 60%.

Unplugged refrigerator and used a screwdriver to remove access panel on rear of refrigerator to expose "mother board". Unplugged connectors (6 total) and using needle nose pliers released two retainers to remove mother board. Installed new mother board snapping it onto the two retainers and plugged the connectors onto the new mother board. Plugged refrigerator into outlet, refrigerator came back on, automatically reset it's temperature settings and has been working fine since. Total time, less than 15 minutes. Money saved, hundreds of dollars!

My problem began with having to replace the auger due to damage (broken blade). Unknown at that time the unit was having a defrost cycle issue. Once auger was repaired, then the motor to auger failed. Once repaired the GE unit then began shutting down without warning. Mother board replaced. All was fine for two weeks then noticed odd performance by ice-maker (chunks of Ice again)and frozen package containers showing signs of dampness and then refreezing. Read through the Parts Select web site to see what other users may have had gone wrong with their GE's and what the parts overview section may reveal for me. Found that the defrost thermo and temp-sensor controlled defrost functions. The parts were cheap, $20.00 for the pair so I replaced them both since they are both located next to one another in the freezer compartment. The repair video furnished on the P/S web was great and very accurate. The entire job only took about an hour. The repair video indicated using wire-nuts and electircal tape Instead, I chose to solder the wires and use shrink-tubing to provide the moisture barrier. PartSelect folks are great not only for their parts pricing but also for the informative videos. The GE works better than ever

First I posted the symptoms on appliance repair forum. Within a very short amount of time, an expert responded with suggestions (that ended up being right on!) and links to How-to articles, diagrams, and the correct parts catalog. They diagnosed it as a failed defrost heater or a bad defrost thermostat that caused the heater to go bad.

I removed all the food from the freezer, removed the shelving and ice maker tray, then removed the back panel (nut driver). The coils were severely iced over. I let the coils defrost (didn't take long in the summer heat). The water from the melted ice completely saturated about two full size bath towels. DO NOT let the coils drain into the normal drain hole. Then I removed the defrost heater (2 screws) and the glass element was dark and cloudy like a burnt-out light bulb.

I placed my order on Parts Select with normal priority shipping. The defrost thermostat was listed as in-stock and the defrost heater was listed as "on order". Both parts arrived 4 days later. The thermostat was a genuine GE part and the heater was a universal aftermarket. My original was a single element heater and the replacement was dual element. The wiring was slightly different, but they included instructions on how to wire up the dual element. The heater wires had to be re-routed and extended (wire cutting, stripping, and crimping are required). The extra length of wire and the wire crimp connector were included with the replacement heater. I also (per the instructions) sealed the crimp connector with RTV sealant. After completing the wiring, I re-attached the heater using the 2 factory screws. Then I had to cut the thermostat wires and splice in using wire nuts (not included) and RTV to seal the connection (not included).

Then I re-attached the back panel using the factory screws and attached the grounding clamp. I installed the shelves and ice maker tray and started the unit. It has been running fine for two weeks now.

The overall repair experience was fantastic. This fridge is only 3 years old and has broken twice in the last year costing me over $500 in food (total for both failures). I also bought a chest freezer last year when the fridge failed the first time. That minimized my frozen food loss this year. The failure last summer was the controller board. I paid the GE technician to come out and fix that because I did not know about this website. I am an engineer and I much prefer the DIY approach, especially when they make it so easy on this website to diagnose and get the right parts.

My only complaints (and they are so minor that complaint might be too harsh of a word) are:
The repair was easy, but would have been significantly easier if they had supplied a direct replacement single element heater.
I wish they would have included the RTV sealant in the repair kit. I happened to have it, but I have to imagine that not everybody will and they won't know that they need it until they read the instructions.
The replacement dual element heater was slightly wider and thus a slightly tighter fit than the original equipment.
Lastly (and this really is no big deal). I got my "Order Shipped" e-mail 6 days after the parts had arrived.

Overall 2 thumbs up!

went to your website and viewed exploded view to find the sensor( there are two I just picked one to replace for now), pried the cover off carfully and pulled out the sensor. I snipped the wire in the middle leaving plenty to work with. I shortened the wire on the new piece, spliced the wires together and with some 3M rubberized, tape wrapped them up, replaced the sensor back into the cover and snapped in place.

put fridge into test mode, failed One sensor. Took it out, Tested it, Ordered part also picked up splice kit from electric store spliced it truned on and good to go

Freezer would not defrost and ice would accumulate on the coils. After the GE repairman quoted me a price to defrost and repair it – which was ridiculous – I decided to tackle the problem myself. I am posting this comment as I found other comments very helpful with trouble shooting my problem. After reviewing other home owner repair comments I decided to first replace the upper sensor, thermostat and heater bracket assy. The longest task to do this was defrosting the coils. What a mess that turned out to be. The items were fairly easy to replace. The sensor and thermostat needed to be spliced and I used good techniques and sealed the splices with electrical tape. Defrost thru repair was about 3.5 hours. Unfortunately, this did not solve the problem and the temperature started rising after the coils froze over again. I decided to go one step further and replace the main board. One repair comment said that it is important to completely remove all of the frost before engaging the new main board – which made sense to me. The defrosting was easier and faster the second time as I plugged the drain below the coils, used hot water and then my shop wet vacuum to remove all the defrost water. Then I reversed the air flow to completely dry the coils. The main board installation instructions were fairly easy to follow. I took a picture with my camera just to ensure all the wires were installed properly. However, that was not necessary the plugs are unique and will only fit one way. The only problem was plugging in the power connector as it was in a different location on the board. With a little careful nudging it was successfully installed. Overall, a good experience and I am thankful for these repair comments by other!

First, I must say that I was told that the mother board might be the problem. I called my husband to tell him what I was told the problem might have been and how much the part was. A little expensive, but still cheaper than calling a repair man. He told me to order the less expensive part first to see if that fixed it. The fan motor. We hung up the phone and for kicks I scrolled down the page to see if it might give any more information on the part and what it controlled, etc. I don't usually read comments, but was amazed at the ones I read. The second comment on the page said that his refrigerator made a whooing sound like a ghost. Our Frig has done this since the day we bought it! He replaced the mother board and the "ghost" moved out! The third comment was that his refirg made a clicking noise and the ice maker doesn't work! I immediately called my husband back and told him I was ordering the part! It arrived the next day. So extremely easy to put in! I removed 3 screws from the cover, disconnected a couple of wires, a few plastic clips; pushed the new part on the clips rehooked the wires and put the cover back on. I bet it took less than 10 minutes! My husband thinks I'm a genius!! Thank you so much for all of your help!

As advised by the forum just replaced the defrost heater assembly now the refrigerator works perfect. did not have to replace the thermostat.
My nephew had exactly same problem on ge refrigerator - replaced the defrost heater assembly and the problem is solved. Just remove the back panel in the freezer compartment, disconnect the cable, remove the nuts and replace the assemble. It is very simple. Bought both assembly from parts select.com - got next day delivery. they are great. would do business in future.

I found if I would put pressure on one connector on the board the unit would come on. So the board had a short. I ordered it, it came in 24 hours and I installed it and problem was solved.